36152
54
Zoom out
Zoom in
Previous page
1/60
Next page
masterpage:Left
lename[E:\SEM_Janet\Revision_HT-
950DP\J9050000_25497361215950DPUS\2549736121\US09ADD_HT-5950DP-CA.fm]
54
US
Model name [HT-5950DP/HT-6900DP/HT-9900M/HT-9950M]
[2-549-736-12(1)]
Dolby Digital or DTS multi channel sound is
not reproduced.
Check that the playing DVD, etc. is recorded in
Dolby Digital or DTS format.
When connecting the DVD player, etc. to the
digital input jacks of this receiver, check the audio
setting (settings for the audio output) of the
connected component.
Recording cannot be done.
Check that the components are connected
correctly.
Select the source component with input buttons.
The FM reception is poor.
Use a 75-ohm coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver to an
outdoor antenna, ground it against lightning. To
prevent a gas explosion, do not connect the ground
wire to a gas pipe.
Radio stations cannot be tuned in.
Check that the antennas are connected securely.
Adjust the antennas and connect an external
antenna if necessary.
The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
No stations have been preset or the preset stations
have been cleared (when tuning by scanning
preset stations). Preset the stations (page 25).
Press DISPLAY repeatedly so that the frequency
appears in the display.
There is no picture or an unclear picture
appears on the TV screen or monitor.
Select the appropriate input on the receiver.
Set your TV to the appropriate input mode.
Move your audio components away from the TV.
Remote control
The remote does not function.
The AUX, MULTI CH** and 12 buttons on the
remote are not available for receiver operation.
Point the remote at the remote sensor on the
receiver.
Remove any obstacles in the path between the
remote and the receiver.
Replace all the batteries in the remote with new
ones, if they are weak.
Check if the command modes of the receiver and
the remote is the same. If the command mode of
the receiver and the remote is different, you
cannot operate the receiver with the remote. To
switch the command mode of the receiver, press
?/1 to turn off the power. Then, press ?/1 while
pressing ENTER. Each time you press ?/1, the
command mode switches between
“C.MODE.AV2” and “C.MODE.AV1”. (The
initial setting is “C.MODE.AV2”.)
Make sure you select the correct input on the
remote.
To activate the buttons with orange printing, press
ALT first before pressing the buttons.
Before you use the V/v/B/b button for receiver
operation, press MAIN MENU. To operate other
components, press TOP MENU/GUIDE or AV
MENU after pressing the input button.
** HT-5950DP only.
AM
ANTENNA
Receiver
To ground
Ground wire
(not supplied)
Outdoor FM antenna
US01COV_HT-5950DP-CA.book Page 54 Monday, April 11, 2005 11:37 AM
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony HT-6900DP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony HT-6900DP in the language / languages: English as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info