527782
12
Zoom out
Zoom in
Previous page
1/120
Next page
10
Using the CUBE
Turning the Power On/O
* Once everything is properly connected (p. 4–p. 9), be sure to
follow the procedure below to turn on their power. If you turn on
equipment in the wrong order, you risk causing malfunction or
equipment failure.
1. Make sure that the CUBE’s [MASTER] knob and the volume
of the devices connected to the CUBE are set to 0.
* Set the [MASTER] knob to 0 before you connect anything to the
CUBE’s INPUT jack or i-CUBE LINK/AUX IN jack.
2. Turn on the power of the devices connected to the CUBE’s
INPUT jack and i-CUBE LINK/AUX IN jack.
3. Turn on the CUBE.
* Before turning the unit on/o, always be sure to turn the volume
down. Even with the volume turned down, you might hear some
sound when switching the unit on/o. However, this is normal and
does not indicate a malfunction.
* This unit is equipped with a protection circuit. A brief interval (a few
seconds) after turning the unit on is required before it will operate
normally.
4. Turn on the power of the devices connected to the LINE
OUT jack (
CUBE-80GX only
) and RECORDING OUT/
PHONES jack.
5. Adjust the volume levels for the devices.
Before switching o the power, lower the volume on each of the
devices in your system and then TURN OFF the devices in the
reverse order to which they were switched on.
* If you need to turn o the power completely, rst turn o the unit,
then unplug the power cord from the power outlet. Refer to “To
completely turn o power to the unit, pull out the plug from the
outlet” (p. 2).
Using SOLO
[SOLO] (MEMORY) button can store the settings of knobs other
than the [MASTER] knob together with either the [JC CLEAN] or
[LEAD] settings.
Storing the Panel Settings
Heres how to store the current settings of the knobs.
NOTE
• When you execute this procedure, the previously stored settings
will be lost.
The stored settings may be lost if you send the CUBE in for
servicing, or if a malfunction occurs, or if an incorrect operation
is performed. Make a note of important settings so that you
won’t be inconvenienced if they are lost. Roland can accept no
responsibility for recovering lost settings, nor for any damages
that may ensue from such loss.
Storing the settings for JC CLEAN
1. Select JC CLEAN, and set
the knobs as desired.
2. Hold down the [SOLO]
(MEMORY) button for
several seconds.
The SOLO (MEMORY) indicator
will blink.
Once the settings have been
stored, the indicator will change
from blinking to lit, and SOLO
will be selected.
Storing the settings for LEAD
1. Select LEAD, and set the
knobs as desired.
2. Hold down the [SOLO]
(MEMORY) button for
several seconds.
The SOLO (MEMORY) indicator
will blink.
Once the settings have been
stored, the indicator will change
from blinking to lit, and SOLO
will be selected.
Calling Up Stored Settings
Heres how to call up the channel and knob positions (settings).
1. Press the [SOLO] (MEMORY) button so it’s lit.
* If you move any knobs after calling up settings from memory, the
settings will change to the positions of the knobs.
* When you operate a knob, the SOLO indicator will light briey when
the knob position matches the stored setting.
Editing and storing SOLO
1. Select SOLO, and set the knobs as desired.
2. Hold down the [SOLO] (MEMORY) button for several
seconds.
The SOLO (MEMORY) indicator will blink.
Once the settings have been stored, the indicator will change from
blinking to lit.
CUBE-20GX
CUBE-40GX
CUBE-80GX
CUBE-20GX
CUBE-40GX
CUBE-80GX
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony DSC-S1900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony DSC-S1900 in the language / languages: German as an attachment in your email.

The manual is 2,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sony DSC-S1900

Sony DSC-S1900 User Manual - Dutch - 94 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info