490838
53
Zoom out
Zoom in
Previous page
1/304
Next page
53
Playback Basics Afspelen
basisbediening
[a]Tijdteller
[b]SteadyShot UIT indicator
[c] Belichtingsfunctie
[d]Kleurbalans-aanduiding
[e]Gevoeligheid-aanduiding
[f] Sluitertijd-aanduiding
[g]Diafragma-aanduiding
Om de andere opnamegegevens niet te zien
Zet in het instelmenu de DATA CODE functie in
de DATE stand (zie blz. 251).
Dan zullen de aanduidingen als volgt veranderen
bij indrukken van de DATA CODE toets van de
afstandsbediening: datum/tijd y green
aanduiding
Vastgelegde gegevens bij opname
Met de opnamegegevens legt de camcorder vast
wanneer en hoe de opnamen zijn gemaakt.
Tijdens het opnemen zullen de opnamegegevens
niet worden aangegeven.
Bij het controleren van de Data Code
opnamegegevens kunnen er wel eens enkel
streepjes (-- -- ----) verschijnen als:
er een blanco (onbespeeld) gedeelte van de
band wordt afgespeeld.
de opnamegegevens op de band niet leesbaar
zijn, door storing of beschadiging van de band.
vóór het opnemen de datum en/of de tijd van
de camcorder niet was ingesteld.
Opnamegegevens op TV
De opnamegegevens kunnen worden
weergegeven op het TV-scherm, als u de
camcorder aansluit op uw TV-toestel.
Resterende batterijtijd-aanduiding tijdens
afspelen
De aanduiding van de resterende batterij-
gebruiksduur geeft bij benadering de beschikbare
speelduur aan. Deze aanduiding kan wel eens
onjuist zijn, afhankelijk van de omstandigheden
van gebruik. Wanneer u het LCD scherm sluit en
weer opent, zal het ongeveer één minuut duren
voordat de juiste resterende batterij-
gebruiksduur weer aangegeven wordt.
Afspelen van een videocassette
[a]Tape counter
[b]SteadyShot OFF
[c] Exposure mode
[d]White balance
[e]Gain
[f] Shutter speed
[g]Aperture value
To not display various settings
Set DATA CODE to DATE in the menu settings
(p. 242).
The display changes as follows when you press
DATA CODE on the Remote Commander:
date/time y no indicator
Various settings
Various settings are your camcorders
information when you have recorded. In the
recording mode, the various settings will not be
displayed.
When you use the data code function, bars
(-- -- ----) appear if:
A blank portion of the tape is being played
back.
The tape is unreadable due to tape damage or
noise.
The tape was recorded by a camcorder without
the date and time set.
Data code
The data code is displayed on the TV screen if
you connect your camcorder to the TV.
Remaining battery time indicator during
playback
The indicator shows the approximate continuous
playback time. The indicator may not be correct,
depending on the conditions in which you are
playing back. When you close the LCD panel and
open it again, it takes about one minute for the
correct remaining battery time to be displayed.
Playing back a tape
Date/time/
Datum/tijd
Various settings/
Diverse opname-instellingen
[g]
[b]
[d]
[e]
[f]
[c]
50 AWB
F2.0 9dB
AUTO
JU4 7 2002
12:05:56 PM
50min
0:00:23:01
50min
0:00:23:01
[a]
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony DCR-TRV24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony DCR-TRV24 in the language / languages: English, Dutch as an attachment in your email.

The manual is 8,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info