291200
122
Zoom out
Zoom in
Previous page
1/192
Next page
122
To add new sound more precisely
Press ZERO SET MEMORY at the point where
you want to stop recording later in the playback
mode.
Carry out steps 3. Recording automatically stops
at the point where ZERO SET MEMORY was
pressed.
Monitoring the new recorded
sound
To play back the sound
Adjust the balance between the original sound
(ST1) and the new sound (ST2) by selecting
AUDIO MIX in the menu settings (p. 132).
About 5 minutes after when you disconnect the
power source or remove the battery pack, the
setting of AUDIO MIX returns to the original
sound (ST1) only. The default setting is original
sound only.
Notes
New sound cannot be recorded on a tape
already recorded in the 16-bit mode (32 kHz,
44.1 kHz or 48 kHz) (p. 136).
New sound cannot be recorded on a tape
already recorded in the LP mode.
New sound cannot be recorded on blank
portions of the tape.
If the i.LINK cable (DV connecting cable)
(optional) is connected to your camcorder
You cannot add a sound to a recorded tape.
We recommend that you add new sound on a
tape recorded with your camcorder
If you add new sound on a tape recorded with
another camcorder (including other DCR-PC8E),
the sound quality may become worse.
If you set the write-protect tab of the tape to
lock
You cannot record on a tape. Slide the write-
protect tab to release the write protection.
Nauwkeuriger inlassen van nieuwe
geluidsopnamen
Druk tijdens weergave op de ZERO SET
MEMORY toets bij het punt waar de nieuwe
geluidsopname moet eindigen.
Volg nu aanwijzing 3. Het opnemen zal
automatisch stoppen bij het punt waar u op de
ZERO SET MEMORY toets hebt gedrukt.
Controleren van het nieuw
opgenomen geluid
Weergeven van de nieuw ingelaste
geluidsopname
Regel de geluidsbalans van de oorspronkelijke
geluidsopnamen (spoor ST1) en het nieuw
ingelaste geluid (spoor ST2) bij door in het
instelmenu voor het onderdeel AUDIO MIX de
gewenste stand te kiezen (zie blz. 132).
Vijf minuten nadat u het batterijpak verwijdert of
de stroomvoorziening onderbreekt, keert de
AUDIO MIX instelling terug naar weergave van
het oorspronkelijke geluidsspoor (ST1). De
begininstelling is voor weergave van alleen het
oorspronkelijk opgenomen geluid.
Opmerkingen
U kunt geen nieuw geluidsspoor inlassen op
een videocassette waarop het geluid is
opgenomen in de 16BIT stand (met 32 kHz, 44,1
kHz of 48 kHz bemonstering) (zie blz. 141).
U kunt geen nieuw geluidsspoor inlassen op
een videoband die is opgenomen met de LP
langspeelsnelheid.
U kunt geen nieuwe geluidsopnamen inlassen
op een onbespeeld gedeelte van de band.
Als het audio/video-aansluitsnoer of de i.LINK
kabel (DV aansluitsnoer) is aangesloten op uw
camcorder
Dan kunt u geen nieuw geluid toevoegen aan een
eerder opgenomen videoband.
Het inlassen van nieuw geluid werkt het beste
voor video-opnamen die met deze camcorder
zijn gemaakt
Inlassen van nieuwe geluidsopnamen op een
videocassette die is opgenomen op een andere
camcorder (ook al was dat een andere
DCR-PC8E) kan resulteren in een minder goede
geluidskwaliteit.
Als de videocassette is beveiligd met het
wispreventienokje
Dan kunt u op deze cassette niet opnemen.
Schuif voor het opnemen eerst het
wispreventienokje terug in de vrije stand.
Audio dubbing Nieuwe geluidsopnamen inlassen
VCR SET
H i F i SOUND
AUD
I
O M
I
X
A
/
VcDV OUT
NTSC PB
ST1 ST2
EXIT
RET.
EXEC
Rr
122


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sony dcr-pc 8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sony dcr-pc 8 in the language / languages: English, Dutch as an attachment in your email.

The manual is 3,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info