680785
17
Zoom out
Zoom in
Previous page
1/28
Next page
Operation/handling
17
The light bulbs may differ depending on the DIP switch:
DIP switch 4 ON,
light bulb (2) is on after the control reset
DIP switch 4 OFF,
light bulb (2) ashes after the control reset.
NOTE!
After a control reset, the drive must be programmed again.
Interim stop
If an interim stop occurs due to the operation of a push-button or the hand-
held transmitter, the drive unit stops immediately. The next command given
sends the drive in the opposite direction. See 'Operation/handling – pulse
sequence of door movement' section.
Safety stop 1
(force cut-off)
When the automatic force cut-off is activated, the drive stops or reverses.
The next command given sends the drive in the opposite direction.
See 'Operation/handling – pulse sequence of door movement' section.
Safety stop when door closes – door reverses
Safety stop when door opens – door stops
Safety stop 2
(safety input)
When the safety input is tripped (e.g. someone crosses light barrier), the
drive stops, reverses or opens, depending on the given DIP switch setting:
See chapter “Functions and connections – obstacle recognition” for
a description of the setting options and DIP switches.
Default settings DIP switch 1 and 3 OFF:
safety input tripped when door closes: door reverses
safety input tripped when door opens: no response (door opens)
Overload protection
If the drive mechanism is subjected to excessive strain when opening or
closing the door, this is recognised by the control unit which then stops the
drive mechanism. After approx. 20 seconds or a control reset, the control
deactivates the overload protection.
The drive mechanism can now recommence normal operation.
Operation following a power failure
The force values remain saved even during a power failure. The rst
movement of the drive after the power is connected must be “door OPEN”.
Radio remote control receiver
HOMELINK COMPATIBLE!
If your vehicle is equipped with a Homelink system (version 7),
you can reach our drive/radio receiver at 868.6 MHz.
With holder Homelink systems, you must use a different
frequency (40.685 or 434.42 MHz). For more information,
please visit: http://www.eurohomelink.com.
Safety instructions
¾ To ensure safe operation, local safety regulations relevant to the
equipment concerned must be observed! Information regarding
this can be obtained from electricity suppliers, the VDE and employers'
liability insurance associations.
¾ The operator of this radio-controlled equipment is in no way protected
from interference from other telecommunications systems and facilities
(e.g. other radio-controlled equipment that is licensed to operate at the
same frequency range).
¾ Try replacing the batteries should reception problems be encountered.
Description of display and push-buttons
5
2
6
3.1
3.2
1
7
7
8
4
5
6
5
2
6
4
3.1
3.2
1
1
Setting button – puts the radio receiver in a given operating mode:
self-learn
delete
normal
2
Internal aerial
3
LEDs – display which channel has been selected.
3.1 LED channel 1
3.2 LED channel 2
4
Connection for external aerial
If the radio range of the internal aerial is not sufcient, you have
the option to connect an external aerial.
5
Hand-held transmitter key
6
External aerial
7
Storage module for radio codes (448) can be plugged in.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Sprint Evolution at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Sprint Evolution in the language / languages: English as an attachment in your email.

The manual is 3,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Sprint Evolution

Sommer Sprint Evolution User Manual - German - 28 pages

Sommer Sprint Evolution User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info