680785
12
Zoom out
Zoom in
Previous page
1/28
Next page
Installation
12
1
HM
3
2
5
4
B
600
0
1
17 18
CAUTION!
Always mount the drive in parallel to the runner rails
of the door.
HM
Lift up drive.
Align ceiling bracket (1). It should be located within a range
of B = 0 ... 600 mm.
Align drive mechanism horizontally to rear centre of door (HM).
Mark position of holes. Drill two holes (Ø 10 x 65 mm deep).
NOTE!
Wear safety goggles when drilling! Check the thickness of the
ceiling, especially in the case of prefabricated garages!
Insert plug (1). Fit two screws (2) with plain washers (3).
Tighten screws (2). Align C-rail (4) at the correct height (use a spirit
level if necessary). If necessary, move screws (5). Tighten screws (5).
19
2
3
5
4
3
N
1
2
4
8
7
3
6
1
20
N
FRONT
VORNE
NOTE!
Use screws that are appropriate to the door material.
Wear safety goggles when drilling!
Mount connecting arm (1):
Insert the long bolt (2) and slide on the securing clip (3).
Attach the door tting bracket (4) to the connecting arm (1) using
the short bolt (5) and slide on the securing clip (3).
Pull once on the emergency release wire (N). The trolley (1)
is disengaged. Tighten screw (8) on the lintel tting.
Push the trolley (1) with the connecting arm (2) as far forward
as possible (3). If necessary, release the switch trigger (4).
Align the door tting bracket (5) to the door centre mark (VM)
and mark 5 drill holes. Drill 5 holes (Ø 5 mm).
Insert hexagon-head screws (6) and tighten securely.
Release the switch trigger (4) and push right up to the trolley (7).
Tighten the switch trigger (4) screw securely.
4
N
1
2
6
4
3
21
5
BACK
HINTEN
NOTE!
Trim (e.g. saw off and debur) the projecting part of the ceiling
bracket (4).
Release the rear switch trigger (1) and push all the way to the back
until the stop (2). Open the door (3) manually.
Push the switch trigger (1) right up to the trolley (5). Securely tighten
the screw on the switch trigger (1).
17
18
18
19
20
20
21
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Sprint Evolution at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Sprint Evolution in the language / languages: English as an attachment in your email.

The manual is 3,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Sprint Evolution

Sommer Sprint Evolution User Manual - German - 28 pages

Sommer Sprint Evolution User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info