680826
44
Zoom out
Zoom in
Previous page
1/96
Next page
44
S10564-00001_Rev-A_EN
INFORMATION
During initial operation:
Stay in the garage, particularly when
programming.
Power deactivation is not yet coordinated
to the door and the operator is in the
programming phase.
The trafc lights light up red in the interior
and the exterior.
INFORMATION
The operating forces can be modied
and adjusted with SOMlink and a WLAN-
enabled device.
Fig. 1
1. Match the existing mains voltage with the type plate.
Connect the operator with the mains voltage.
Check that the power supply is connected.
The status LED of the carriage ashes green.
Operator ready for commissioning.
INFORMATION
Depending on which accessories are
connected, additional LEDs light up for the
respective state on the circuit board of the
control unit.
START IN
Fig. 2
2. After the operator has been connected to the main
voltage, its first movement after a pulse is always
door OPEN.
Press the START IN button on the tiga control unit.
The carriage moves slowly to the door OPEN end
position and automatically switches off at the
guide idler.
The operator lighting ashes.
START IN
Fig. 3
3. Press the START IN button on the tiga control unit
again.
The carriage moves slowly in the door CLOSE
direction.
The operator lighting ashes.
The carriage switches off automatically when it
reaches the factory-set closing force at the door
CLOSE end position.
The operator lighting ashes in a different
sequence.
67$57,1
Fig. 4
4. Press the START 1 button on the tiga+ control unit
briefly (< 1 second) to save the end position.
The operator lighting ashes briey in a fast
sequence.
The operator automatically starts its
programming process:
The carriage moves automatically to the door
OPEN end position and programs the required
operating force.
The carriage automatically moves to the door
CLOSE end position.
If necessary, the carriage moves over the path
several times for programming with a greater door
weight.
9. Commissioning
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9080 Tiga at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9080 Tiga in the language / languages: English as an attachment in your email.

The manual is 28,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9080 Tiga

Sommer S 9080 Tiga User Manual - German - 96 pages

Sommer S 9080 Tiga User Manual - Dutch - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info