680551
52
Zoom out
Zoom in
Previous page
1/80
Next page
52
46900V001_Rev-D_EN
11. Connections and special functions of the ceiling
control unit
5. Connect the cable of button 2 to the terminal block
for COM and Signal.
Button 2 is connected.
6. Set DIP switch 4 on the wall device to ON.
7. Plug in the connection cable for the button and for
the accumulator, if necessary.
8. Close the ceiling control unit in reverse order,
see Chapter "11.11 Installing and removing
the accumulator" and "7.2 Cover of the ceiling
control unit".
9. Supply the operator with the mains voltage.
Settings on the motor carriage
To determine the partial opening door position, the
following settings must be made on the motor carriage.
1. Close the door completely up to the door CLOSE
end position.
2. Open the motor carriage, see chapter "7.1 Cover of
the motor carriage".
3. Set DIP switch 2 on the motor carriage to ON.
4. Press button 2 for the partial opening function.
The door moves in door OPEN direction.
5. Press button 2 again for the desired position for
stopping.
The door stops at the desired position.
11.5 Deleting partial opening
1. Set DIP switch 2 on the motor carriage to OFF.
2. Open the door completely up to the door OPEN end
position.
Partial opening is deleted.
To program a new position, see Chapter "10.17 Setting
partial opening".
11.6 Photocell and frame photocell
A 2-wire photocell from SOMMER or a 4-wire photocell
can be connected to the control unit. The control unit
automatically detects which version it is and sets itself to
that version.
Fig. Terminal for a 2-wire photocell
WL
24V/1A
Signal
COM
GND
+24V
O
12
WL
2
4V
/
1
A
O
1
2
Fig. Terminal for a 4-wire photocell
INFORMATION
If a photocell is retrotted on a programmed
system, the control unit must be reset, see
Chapter "10.13 Resetting the control unit."
INFORMATION
If a photocell is used, it must not be
triggered when starting the programming.
If a photocell is used as a frame photocell
on the door, move the door to the centre
position.
INFORMATION
During commissioning, the frame photocell
must not be interrupted by persons or
objects.
Frame photocell
1. Install the frame photocell in the frame, see separate
"Frame photocell" installation instructions.
2. Align the frame photocell and connect to the ceiling
control unit.
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 base at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 base in the language / languages: English as an attachment in your email.

The manual is 8,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 base

Sommer S 9060 base Installation Guide - German - 80 pages

Sommer S 9060 base Installation Guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info