680551
35
Zoom out
Zoom in
Previous page
1/80
Next page
35
46900V001_Rev-D_EN
9. Commissioning
9.2 Initial operation
Before initial operation, read this chapter with special
care to ensure that you can make the adjustments to the
operator safely and optimally.
WARNING
Danger of entrapment!
If the force setting is too high, persons
or animals in the movement area of the
door may be trapped and pulled along
with the door. Severe injuries or death
may result.
The force setting is relevant to safety
and must be carried out by a trained
specialist.
You must proceed with extreme caution
if you check and if necessary adjust the
force setting.
Please note that the operator may only
be operated if a non-hazardous force
value has been set.
Select the force setting low enough to
eliminate any danger of injury by the
closing force.
NOTE
Do not use a metal object to set the
DIP switches, because this may damage
the DIP switches or the circuit board.
Use a suitable tool to set the DIP switches,
such as a at, thin plastic object.
INFORMATION
The force setting must be checked after
installation of the operator. See also
chapter "13.1 Testing obstacle detection."
The operator may only be used:
in combination with door types in the reference list
which can be found at:
http://som4.me/cgdo
For compliance with EN 13241-1, before initial operation,
the door type must be selected and set on the motor
carriage with the DIP switch.
The factory setting of the DIP switches on the motor
carriage is "OFF", which is then applicable for sectional
doors.
DIP switch on
motor carriage
ON
OFF
1
ON
1
2
3
4
Automatic
closing function
activated
Automatic
closing
function
deactivated
2
ON
1
2
3
4
Partial opening
activated/
Lighting
function
deactivated
Partial
opening
deactivated/
Lighting
function
activated
3+4
ON
1
2
3
4
3
ON
1
2
3
4
4
ON
1
2
3
4
The motor carriage has an automatic force setting. The
motor carriage memorizes the required force during the
OPEN and CLOSE door movements and stores it when
the end position has been reached.
INFORMATION
During initial operation:
Stay in the garage, particularly when
programming.
Obstacle detection has not yet been
coordinated with the door, and the
operator is in the programming phase.
INFORMATION
The operating forces can be modied and
adjusted with SOMlink and a WiFi-enabled
device.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9060 base at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9060 base in the language / languages: English as an attachment in your email.

The manual is 8,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9060 base

Sommer S 9060 base Installation Guide - German - 80 pages

Sommer S 9060 base Installation Guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info