680774
9
Zoom out
Zoom in
Previous page
1/88
Next page
9
S10931-00001_Rev-D_EN
asspeciedinthisInstallationandOperatingManual
in good technical condition
with attention to safety and hazards by trained users.
1.9 Improper use of the operator
Any other use or additional use that has not been
described in chapter "1.8 Intended use of the operator"
constitutes improper use. The user bears the sole
responsibility for any risk involved.
The manufacturer's warranty will be voided by:
damage caused by other use and improper use
use with defective parts
unauthorisedmodicationstotheoperator
modicationsandnon-approvedprogrammingof
the operator and its components
The door must not be part of a fire protection system,
an escape route or an emergency exit that automatically
closes the door in the event of fire. Installation of the
operator will prevent automatic closing. Observe the local
building regulations.
The operator may not be used in:
areas with explosion hazard
very salty air
aggressive atmosphere, including chlorine
1.10 Qualifications of personnel
People under the influence of drugs, alcohol, or
medications that can influence their ability to react may
not work on the operator.
After installation of the operator, the person responsible
for the installation of the operator must complete an
EC Declaration of Conformity for the door system in
accordance with Machinery Directive 2006/42/EC
and apply the CE mark and a type plate to the door
system. This also applies if the operator is retrofitted
to a manually operated door. In addition, a handover
protocol and an inspection book must be completed.
The following are available:
handover protocol for the operator
EC Declaration of Conformity
http://som4.me/konform
Qualied specialist for installation,
commissioning and disassembly
This Installation and Operating Manual must be read,
understood and complied with by a qualified specialist
who installs or performs maintenance on the operator.
Work on the electrical system and live parts must be
performed by a trained electrician in accordance with
EN 50110-1.
Installation, initial operation and disassembly of
the operator may only be performed by a qualified
specialist.
The qualified specialist must be familiar with the following
standards.
EN 13241-1 Doors and gates – Product standard
EN 12604 Doors and gates – Mechanical aspects –
Requirements
EN 12605 Doors and gates – Mechanical aspects –
Test methods
EN 12445 and EN 12453 – Safety in use of power-
operated doors
A qualified specialist is a person commissioned by the
installer. The qualified specialist must instruct the user:
on the operation of the operator and its dangers
on the handling of the manual emergency release
on regular maintenance, testing and care which the
user can carry out
The user must be informed that other users must be
instructed on the operation of the operator, its dangers
as well as the emergency release.
The user must be informed about which work may only
be performed by a qualified specialist:
installation of accessories
settings
regular maintenance, testing and care
troubleshooting and repairs
The following documents for the door system must be
handed over to the user:
EC Declaration of Conformity
handover protocol and inspection book
the installation and operating manuals for the
operator and the door
1. About this Installation and Operating Manual
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9050 pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9050 pro in the language / languages: English as an attachment in your email.

The manual is 10,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9050 pro

Sommer S 9050 pro User Manual - German - 88 pages

Sommer S 9050 pro User Manual - Dutch - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info