680550
72
Zoom out
Zoom in
Previous page
1/80
Next page
72
46900V001_Rev-D_EN
16. Troubleshooting
16.4 Troubleshooting table
Problem Possible cause Test/check Remedy
The operator opens
the door when the
transmitter or control
device is actuated but
does not close it.
Photocell and safety
device interrupted
Check photocell and safety
devices
Remove obstacle
The photocell must be aligned
Have it checked and replaced by a
qualiedspecialist
Automatic closing
function activated
Wait to see whether the
operator starts automatically
after 30 seconds
Automatic closing function
deactivated
Have the cause corrected by a
trained electrician
Operator cannot be
operated with the
control device.
No power Check power supply Check the power socket with a
different device, for example by
plugging in a lamp
Limit switch on motor
carriage defective
Unlock operator and push
motor carriage to the centre of
the track
Lock operator
Actuate transmitter
If the operator still closes the
door but does not open it,
the limit switch is defective
Have the limit switch replaced by a
qualiedspecialist
The operator was
unlocked by the
emergency release
mechanism
Check that the door can be
moved manually
Pull the emergency release handle
to lock the operator
Control device
incorrectly connected to
the operator
Check function of operator
with a transmitter
Check wiring, correct if necessary
Transmitter defective Operator cannot be started
with the transmitter
Check transmitter power supply
If necessary, replace the battery of
the transmitter
If necessary, replace the
transmitter with a new one
Operator defective Operator cannot be started
with the transmitter or the
connected control device
Have operator repaired or
replacedbyaqualiedspecialist
Electrical supply voltage
outside the approved
range
Have the mains voltage
checked by a trained
electrician
Have the cause corrected by a
trained electrician
When a button on
the transmitter is
pressed, the door
does not open or
close.
Transmitter not
programmed
Radio LED does not light
up when the transmitter is
operated
Programme transmitter
Battery in the
transmitterisat
Replace the battery of the
transmitter
Transmitter defective LED on transmitter does not
light up
Replace transmitter
Radio command
cannot be
programmed.
Memory full All four LEDs for radio blink
cyclically for about 3 seconds
Memory full, see Chapter
"10.6 Information on Memo"
and "10.8 Deleting a transmitter
button from the radio channel"
MEMO Identier error Incorrect MEMO • All four LEDs blink cyclically
for a short time and then
go out for a long time. The
operator lighting of the motor
carriage blinks 4 times short
and 4 times long.
Disconnect operator from the
power supply, unplug Memo,
re-supply operator with power
MEMO device type
error
System error All four LEDs blink cyclically
for a long time and then go
out for a short time. If voltage
is present, the operator
lighting of the motor carriage
blinks an additional four times.
Memo can be deleted via
the Radio button, see Chapter
"10.8 Deleting a transmitter
button from the radio channel"
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9050 base plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9050 base plus in the language / languages: English as an attachment in your email.

The manual is 8,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9050 base plus

Sommer S 9050 base plus Installation Guide - German - 80 pages

Sommer S 9050 base plus Installation Guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info