680550
64
Zoom out
Zoom in
Previous page
1/80
Next page
64
46900V001_Rev-D_EN
14. Operation
14.4 Obstacle detection
The operator stops and reverses slightly if it encounters
an obstacle. This prevents injury and damage to
property. The door will be partially or completely opened
depending on the setting.
The partial reversion is pre-set at the factory. Full reversion
can be set via SOMlink and a WiFi-enabled device.
INFORMATION
Reversing: The operator stops when it
hits an obstacle. Then the operator moves
slightly in the opposite direction to release
the obstacle.
In the automatic closing function the door
opens completely.
The following safety devices are installed to detect
obstacles:
photocell (object protection)
safety contact strips (personal protection)
obstacle detection of operator (personal protection)
See also Chapter "15. Maintenance and care".
14.5 Power-saving mode
To save energy, the operator control unit switches to
power-saving mode after the factory-specified period.
Connected accessories are deactivated and then
reactivated at the next command from a button or radio.
Connected accessories may include: photocell, safety
contact strip and external radio receiver.
Because external radio receivers are deactivated in
power-saving mode, they cannot receive commands from
the remote control and send them to the operator.
Set DIP switch 3 to ON to power the entire system
continuously. Power-saving mode is deactivated.
DIP switches
on the ceiling
control unit
ON OFF
3
ON
1234
Continuous
power to the
complete
system
activated
Power-
saving mode
activated
INFORMATION
The factory-set period before the control
unit switches to power-saving mode is
20 seconds. This value cannot be changed.
14.6 Operation during power failure
The programmed force values and end positions of the
operator remain saved in the event of a power failure.
After the power supply has been restored, the first
movement of the operator after a pulse is always
door OPEN. The door moves the entire way into the door
OPEN end position.
Also follow the instructions for emergency release
in Chapter "11.11 Installing and removing the
accumulator" or "14.7 Function of the emergency
release".
14.7 Function of the emergency release
In the event of a power failure, the door can be opened
and closed manually from the inside using a mechanical
emergency release.
Observe in particular the following safety instructions for
this chapter.
WARNING
Danger for trapped persons!
Persons may be trapped inside the
garage. If trapped persons cannot free
themselves, severe injury or death may
result.
Test the operation of the emergency
release regularly from inside and if
necessary, also from outside.
You must have faults repaired
professionally without delay.
WARNING
Danger due to falling parts of
doors!
If the emergency release is actuated,
weak or broken springs may cause
the door to close suddenly and
unexpectedly.
This may cause serious or fatal injury.
The emergency release should be used
only with the door closed.
Use the emergency release with great
caution if the door is open.
Keep persons and animals clear of the
range of movement of the door.
NOTE
The emergency release is only suitable
for opening or closing the door in an
emergency.
The emergency release is not suitable for
regular opening or closing. This could
cause damage to the operator and door.
The emergency release must only be used
in emergencies such as a power failure.
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer S 9050 base plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer S 9050 base plus in the language / languages: English as an attachment in your email.

The manual is 8,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer S 9050 base plus

Sommer S 9050 base plus Installation Guide - German - 80 pages

Sommer S 9050 base plus Installation Guide - Dutch - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info