474215
9
Zoom out
Zoom in
Previous page
1/32
Next page
Installation
9
1
a
b
1
3
2
FRO
N
T
VO
RN
E
2a 2b
1
2
2
1
1
1
2
3
3a 3b
5
a
c
90°
b
1
2
3
4
5
6
FRONT
V
ORNE
FR
ONT
V
ORNE
Pre-installation
Open both packages and inspect the delivery scope.
NOTE!
Dispose of the packaging according to locally applicable
regulations.
Remove both C-rails (8), connecting sleeve (9) and controller housing (1)
from the packaging (see chapter “General information – delivery scope”),
place in the garage (the controller housing (1) is located inside the garage)
and have tools readily at hand.
ATTENTION!
Make sure that all components are not lying directly on a hard
surface. To protect the components, place cardboard, covers
or other soft surfaces underneath.
Insert the chain (2) from behind into the carriage (1).
Ensure that the chain (2) lies correctly on the chain wheel (3).
Put the carriage contact springs in place. Slide the carriage (1)
with chain onto the rails (2) with the red guide idler.
The tip of the guide idler must point toward the carriage (1).
Push the chain through the guide idler.
Push the two rails (1) over the connecting sleeve (2) up to the stop
position. You now have a single continuous rail. When pushing the rails
together, ensure that the chain is guided through the guide idler.
The tip of the guide idler must point toward the carriage (1).
2a
2b
Push the controller housing up to the stop position at the rear of the
rail and put the carriage contact springs in place. Make sure that the
chain attachment bolt of the controller housing runs on the same side
as the chain.
Insert the screws (3) into the ceiling holder (2). Push the ceiling holder
with inserted screws onto the rear end of the rail. The guide idler
is located at the rear end of the rail.
3a
3b
4
B
A
C
K
H
IN
T
E
N
1
2
3
IMPORTANT!
The wiring grommet must be on the bottom of the controller
housing.
The chain (1) is connected to the chain attachment bolt of the controller
housing (2) by means of the chain lock (3).
a) Hook the tensioner (1) into the chain (2).
b) Turn the tensioner 90°.
c)
Push the slide-in part (6) in the rail and insert the tensioner.
Put the washer (5) and spring (4) on the tensioning screw (3)
and screw the tensioning screw (3) into the tensioning element.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Marathon 800SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Marathon 800SL in the language / languages: English as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Marathon 800SL

Sommer Marathon 800SL User Manual - German - 32 pages

Sommer Marathon 800SL User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info