If your vehicle is equipped with a HomeLink system (Version 7), our drive and radio receiver with 868.6 MHz are compatible.
Another radio frequency (40.685 or 434.42 MHz) must be used with older HomeLink systems. Information can be found under
http://www.eurohomelink.com or contact your specialist dealer.
IMPORTANT!
Many malfunctions can be resolved by a controller reset (delete force values), then reprogram the drive.
If you cannot fi nd the malfunction in the table and eliminate it, take the following actions:
• Perform a controller reset (delete force values) on the controller.
• Disconnect connected accessories (e.g. photo eyes) and reconnect the jumper for a safety connection.
• Set all DIP switches to the factory setting.
• If settings have been changed using TorMinal, perform the controller reset with TorMinal.
• Check all connections on the direct connectors and terminal strip and retighten if necessary.
Drive malfunctions can be corrected according to the following table. If this does not help, contact your specialist dealer for assistance or consult our
website at http://www.sommer.eu.
MalfunctionPossible causesCorrective action
Lighting blinks.Drive has not been programmed,
no force values stored.
Program the drive. See chapter “Using for the fi rst time –
programming the drive”.
Drive does not function and lights do not
light up.
No voltage present.Stick in the power mains plug.
No controller installed.Install controller.
Circuit breaker for garage circuit has
tripped.
Replace circuit breaker, check circuit with a different consumer
device (e.g. electric drill).
No lights when opening and closing
the door.
Defective bulb.Replace light bulb. See chapter “Care and maintenance/regular
testing”.
Drive doesn't function.Controller incorrectly installed.Plug controller correctly into terminal strip.
Photo eyes interrupted,
safety LED lights continuously.
Remove interruption.
The (8.2 kOhm) safety contact strip is
defective or DIP switch 2 is ON; the
Safety LED lights up.
Replace the safety contact strip or set DIP switch 2 to “OFF”.
Fraba system switched on but photo
eyes or safety contact strip (8.2 kOhm)
connected, safety LED lights
continuously.
Switch off the Fraba system; set DIP switch 2 to OFF.
Drive does not function when operated
with a hand-held remote control.
Battery in the hand-held remote control
is empty.
Replace battery with new one.
The hand-held remote control has
not been programmed for the radio
receiver.
Programming the hand-held remote control.
Incorrect radio frequency.Check the frequency (868/434 MHz, without external antenna).
The command is constantly pending
because the button of the hand-held
remote control is stuck.
Release the key or replace the hand-held remote control.
Drive does not function when button-
operated.
Button not connected or is defective.Connect button or replace it.
Door stops while closing, moves about
10 cm in the opposite direction, and
stops.
Force cut-off actuated by an obstacle.Remove obstacle, open door completely.
Incorrect force values programmed or
force tolerance set too low.
Delete force values and reprogram.
Guide idler incorrectly adjusted.Readjust the guide idler, see the chapter “Commissioning –
Salve ho acquistato un garage con l'automatismo Marathon 550 sl . Non ho più i telecomandi , sono andati perduti . Come devo fare ???? Stefano
Submitted on 26-4-2023 at 16:09
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Sommer Marathon 550SL at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Sommer Marathon 550SL in the language / languages: English as an attachment in your email.
The manual is 4,22 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
