680841
10
Zoom out
Zoom in
Previous page
1/36
Next page
Installation sprint / marathon
9
For installation on the ceiling (D), drill holes at distances of
15 mm, if possible. Smaller angle of inclination of the fixing
brackets.
The drive mechanism can be mounted on lintel (S) or ceiling (D).
Measure front centre point (VM) of door and mark on door and on
lintel or ceiling.
Make a mark 74 mm to right and left of centre of door (VM) at same
height on lintel or ceiling (see fig. 8).
Drill two holes (Ø 10 x 65 mm).
Wear safety goggles when drilling!
Check thickness of ceiling, particularly with prefabricated
garages!
Open door. Transfer door centre mark (HM) on to ceiling. Close door.
Insert plug (1). Lift up drive mechanism (2) at front. Secure lintel
fitting (3) at front with two screws (4) and plain washers (5).
Protect control unit housing (6) from damage!
14
1
HM
3
2
5
4
B
600
0
1
13
8
S
30
min.15
30
15
15
D
½½
½½
½
½
VMVMVM
9
12
12
2
6
4
5
31
11
10
15
½½
½½
½
½
HMHMHM
11
VM
74mm 74mm
10mm
65mm
10
THP
9
8
Caution!
Mount the drive in parallel to the runner rails of the door.
Lift up drive
Align ceiling bracket (1). It should be located within a range of
B = 0 ... 600 mm.
Align drive mechanism horizontally to rear centre of door (HM). Mark
position of holes. Drill two holes (Ø 10 x 65 mm deep).
Wear safety goggles when drilling!
Check thickness of ceiling, particularly with prefabricated
garages!
Insert plug (1). Fit two screws (2) with plain washers (3). Tighten
screws (2) securely.
Align C-rail (4) at correct height. If necessary, move screws (5).
Tighten screws (5).
Mount drive shaft (1):
Insert the long bolt (2) and slide on the securing clip (3).
Attach the door hinge (4) to the connecting rod (1) using the short
bolt (5) and slide on the securing clip (3).
Pull once on emergency release wire (N), thus disengaging bogie
unit (1). Tighten screw (8) on lintel fitting.
Use drive shaft (2) to push bogie unit (1) as far forward as possible
(3). If necessary, release cut-off buffer (4).
Align angle of door fitting (5) with centre of door (VM) and mark
5 drill holes. Drill 5 holes (Ø 5 mm).
Use screws that are appropriate to the door material.
Wear safety goggles when drilling!
Insert 5 hexagon-head screws (6) and tighten securely.
Release cut-off buffer (4) and push right up to bogie unit (7).
Tighten cut-off buffer screw (4) securely.
16
15
15
2
3
5
4
3
N
1
2
48
7
3
6
5
1
N
16
14
13
HM
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sommer Duo 500SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sommer Duo 500SL in the language / languages: English as an attachment in your email.

The manual is 4,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sommer Duo 500SL

Sommer Duo 500SL User Manual - German - 37 pages

Sommer Duo 500SL User Manual - Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info