536051

Somfy Elixo 500 24 V Manual

4
Zoom out
Zoom in
Previous page
1/16
Next page
2 Copyright © 2008 Somfy SAS. All rights reserved.
EN
Elixo 500 24 V
This product, installed in accordance with this guide, complies with EN 12453 and EN 13241-1 standards.
Somfy hereby declares that this product complies with the essential requirements and other relevant provisions of
Directive 1999/5/EC. A Declaration of Conformity is available at the web address www.somfy.com/ce (Elixo 500 24 V).
Suitable for use in EU, CH and NO.
General information
Always read this installation manual and the safety instructions before installing this Somfy product.
This Somfy product must be installed by a professional motorisation installer, for whom these instructions are intended.
The use of any safety components not approved by Somfy remains the sole responsibility of the installer.
These instructions describe how to install, commission and operate this product.
Moreover, the installer must comply with current standards and legislation in the country in which the product is being
installed, and inform his customers of the conditions for use and maintenance for the product.
Any usage outside of applications defi ned by Somfy constitutes non-compliance, and is therefore not covered by
the guarantee. In this event, as for all usage not consistent with the instructions given herein, Somfy accepts no
responsibility for harm or damage.
Safety instructions
Before installation, ensure that the gate frame conforms to current standards, particularly:
The gate sliding rail must be straight and horizontal and the wheels must be able to support the weight of the gate.•
The gate should move easily over its entire travel distance and there should be no sign of excessive side sway.•
The upper guide should allow the gate exact clearance to ensure regular, silent movement.•
End stops must be installed on the ground at both the opening and closing stop positions.•
The position in which the motorisation mechanism will be fi tted must allow for safe and easy manual release. •
If after evaluation the gate system does not meet the conditions set out above, it must be repaired or, if necessary,
replaced.
The selected safety accessories for the installation must comply with the current standards and regulations in force in the
country in which the product is being installed.
Ensure that there are no danger zones (risk of crushing, cutting, trapping), between the gate and the surrounding fi xed
elements, caused by the opening movement of the gate.
On a barred gate, if the bars are more than 40 mm apart, install an appropriate safety device to prevent cutting.
Maintain a clear area of 500 mm behind the gate when it is completely open.
Take care while the gate is moving.
Place the fi xed control devices and remote controls out of the reach of children.
Any switch without a locking device must be installed in direct view of the gate and away from any mobile parts. The
minimum height at which it must be installed is 1.5 m. It must not be accessible to the public.
During installation of the motorisation:
Remove any jewellery (bracelets, chains, etc.).•
For drilling and welding operations, wear special glasses and suffi cient protection.•
Use the appropriate tools.•
Do not connect to the mains or to a backup battery before installation is complete.•
Be careful when handling the motorisation system to prevent any risk of injury.•
In order to operate, the motorisation must be supplied with 230 V 50 Hz. The electric supply should:
solely be used for the motorisation,•
have a minimum cross section of 1.5 mm²,•
be fi tted with an approved all-pole switch with contact openings of at least 3.5 mm, fi tted with a protection device •
(fuse or circuit breaker with a 16 A rating) and a differential device (30 mA),
be installed in accordance with the current electrical safety standards.•
It is recommended that the installation be fi tted with a lightning conductor (in compliance with standard NF C 61740,
maximum residual voltage 2 kV).
When installation is complete, ensure that the mechanism is correctly set and that the gate changes direction when it
encounters an obstacle.
GENERAL INFORMATION
SAFETY
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Somfy Elixo 500 24 V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Somfy Elixo 500 24 V in the language / languages: English as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info