655959

Solo 880 Manual

77
Zoom out
Zoom in
Previous page
1/249
Next page
Operating and maintenance notes
ENGLISH 35
x Proper electrode distance: 0.5 mm [approx. 0.02"]
Replace the spark plug if the electrode distance is incorrect.
The following interference-suppressed spark plugs are approved for
use in this power tool:
BOSCH WSR6F, CHAMPION RCJ-6Y and NGK BPMR7A
Use of other spark plugs is not allowed!
x Check ignition cable (c) for proper connection and intact insulation. If the insulation is damaged, do not
continue work, but order repair from a specialist workshop authorised by us.
x Screw in spark plug (d) again. Torque: 25 Nm [18.4 ft·lbf]
x Push the spark plug connector (b) onto the spark plug (d) firmly at reattachment.
x Re-install the spark plug cover (8).
Danger of contamination of ribbed belt, associated carrier structure and coupling!
Only open the ribbed belt cover and coupling cover in a clean environment.
x Switch off the engine and turn the stop dial to "0".
Switching off the engine: Î Chap. 6.4, page 25
x Shut off water supply to the power tool.
x Put the power tool on level ground.
x Loosen both attachment nuts (a) of the ribbed
belt cover (14).
x Turn ribbed belt tension screw (13) towards the
left, e.g. counter-clockwise, to reduce the ribbed
belt tension).
Turn until the square nut (b) has been moved
 (c) as far as possible.
When installing the cutting device in the centre
position (cf. figure), the square nut is all the way
to the left; in case of installation in the outer
position, it is located all the way to the right.
x Remove both attachment nuts (a) entirely.
x Remove the ribbed belt cover (14).
x Screw the attachment nuts (a) of the ribbed belt
cover (14) onto the associated screws again and
tighten only slightly so that the separating device
cannot fall off again.
x Loosen all 3 attachment screws (d) of the
coupling cover (e).
The screws only need to be loosened until they
can be turned very easily. It is not necessary to
turn out the screws entirely, since the screws
should remain in the cover.
8.6 Ribbed belt replacement
0.5 mm [approx. 0.02"]
14
b
a
13
c
e
d
28
… 77 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 880 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info