658828

Solo 652 Manual

13
Zoom out
Zoom in
Previous page
1/26
Next page
Starting / Stopping the engine
- 35 - ENGLISH 13
8.2 Starting up
Please read the safety instructions before starting up
the device.
(schematic diagram)
Take off the chain guard.
Place the power tool on level ground which is free of
obstructions and make sure that the cutting tool is
not touching anything.
Place one foot in the rear handle to secure the saw
on the ground. Use one hand to firmly hold the saw
by the front handle.
Alternative way to hold the saw while starting it up
(for experienced users only):
(schematic diagram)
Firmly grasp the rear handle between your thighs.
Use one hand to firmly hold the saw by the front
handle.
You must make absolutely sure that there is no
risk of contact between the guide bar and any
part of your body.
The following instructions are intended to extend the
service life of the starter cable and the starter
mechanism:
• To start with, pull the cable carefully until a first
resistance is felt, then pull it through in a fast and
strong motion.
• Always pull the cable in a straight direction.
• Do not allow the cable to chafe on the edge of the
cable eyelet.
• Avoid pulling the cable all the way out – risk of
breaking the cable.
• Always guide the starter handle back to its starting
position – do not just let go and allow it to speed
back by itself.
A damaged starter cable can be replaced by a
specialist.
When the engine is running,
lift up the power tool
and hold it safely with both hands, then briefly
operate the throttle control to cancel the part throttle
setting.
8.3 Engine will not start:
If the engine fails to start after several attempts,
check whether all adjustments described above have
been correctly carried out, particularly that the stop
switch is not in the "0" position. Try starting once
again. The combustion chamber will be flooded, if the
engine still fails to start.
In that case we recommend you proceed as follows:
• Remove the cowl.
• Pull the spark plug cap off the spark plug.
• Remove the spark plug and dry fuel mixture from
the electrodes.
• Move the throttle lever up to full throttle. Pull the
starter handle several times (with removed spark
plug) to clear the combustion chamber.
• Move the throttle lever down to idling position, refit
the spark plug, the plug cap and the cowl.
• Repeat the starting process according to the
starting settings for a warm start.
8.4 Switching the engine off::
Release the throttle control and move the stop switch
to the "0" position.
Always make sure that the cutting tool has come
to a complete standstill before placing the
machine down.
Tip: As it can sometimes happen that, after a
brief/intermediate stop, the starting settings are not
set up correctly before the machine is restarted (in
particular, the stop switch may still be set to "0" and
the chain brake may not have been applied), we
recommend that users should get in the habit of
immediately applying the chain brake whenever the
machine is temporarily switched off and the engine
comes to a complete standstill and of setting the stop
switch back to the "Operating“ position.
As a general rule, you should always check the
starting settings before every start.
Switching the engine off in the event of a malfunction:
If – due to a malfunction of the stop switch – it is not
possible to switch the engine off, you can also close
the choke flap
(choke pulled out) to bring the
engine to a standstill. In this case do not restart the
tool – have it checked out immediately by a specialist
workshop instead!
Fig. 8
Fig. 9
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 652 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 652 in the language / languages: English as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Solo 652

Solo 652 User Manual - German - 24 pages

Solo 652 User Manual - Dutch - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info