658828
5
Zoom out
Zoom in
Previous page
1/26
Next page
Safety regulations
- 27 - ENGLISH 5
1.3 Fuelling
Petrol is very light and highly flammable. Keep away from open flames and never spill fuel. Do not
smoke at the operating site or at and near the refuelling site!
Stop the engine prior to refuelling.
Let the engine cool down before refuelling - fire risk!
Open the tank lid slowly to allow any excess pressure in the tank to be reduced without the risk of petrol
spraying out.
Fuel may contain substances similar to solvents. Prevent products made from mineral oil coming into
contact with skin and eyes. Wear protective gloves during filling with fuel. Frequently change and clean
protective clothing.
Avoid breathing in fuel vapour.
The refuelling site should be well ventilated.
Avoid any soil spillage of fuel or oil (protection of the environment). Use a suitable mat.
Immediately clean any spilled fuel on the machine. Change contaminated clothing without delay.
Always tighten the fuel tank cap firmly by hand without using any tools. The fuel tank cap must not be able
to work itself loose as a result of the vibrations of the engine.
Check for petrol leaks. Do not start the machine or work with the machine if there is a petrol leak. Life
threatening risk from burns!
Store fuel and oil in approved and correctly labelled containers.
1.4 When transporting the equipment
When carrying the chainsaw for short distances (from one working area to the next), always apply the chain
brake so that the chainsaw is blocked (preferably switch the engine off as well).
Never carry or transport the power tool while the cutting tool is running.
When transporting the device over longer distances, always switch the engine off and attach the chain
guard.
To prevent leakage of fuel or oil and damage in general, make sure that the device is secured so that it
cannot fall over when it is transported in vehicles. Check the fuel and chain lubrication tanks for leaks.
Ideally you should drain the tanks prior to transport.
Always empty the tanks before dispatching the unit.
1.5 Notes on assembly, cleaning, adjustment, maintenance and repairs
The power tool must not be assembled, maintained, repaired or stored in the vicinity of naked flames.
The engine must be switched off and the stop switch set to "0“ for the duration of all work performed on the
guide bar and saw chain (for assembly, cleaning, maintenance and repairs) (ideally the spark plug
connector should be unplugged as well). Always use protective gloves.
The power tool requires regular maintenance. Only perform maintenance or repairs yourself if the relevant
operations are covered in the operating instructions. All other work should be performed by an authorised
specialist workshop.
During maintenance of the silencer or when checking that the silencer is firmly positioned, never touch the
silencer if it is still hot – risk of burns! The silencer gives off extremely large amounts of heat.
Only genuine replacement parts supplied by the manufacturer must be used for any repairs.
No changes must be made to the power tool, as this could affect the safety of the device and increase the
risk of accident or injury.
1.6 Before starting the tool
Check the tool every time before starting it to make sure that the complete power tool is operationally safe. The
following points should be checked in addition to the points listed in the operating and maintenance
instructions (chapter 11):
The stop switch must be easy to switch.
The throttle control must move freely and return automatically to the idle position. If the throttle control is
operated while the choke lever is pressed in then this must cancel any part throttle stop that is set.
The guide bar must be firmly secured. Always check that the chain has the correct tension and adjust the
tension if required before starting the tool.
Also check that the ignition cable and spark plug connector are firmly in place. If there is a loose connection
this can result is sparks which could ignite any escaping fuel/air mixture – fire hazard!
If anything is not as it should be, signs of damage are evident, settings are incorrect or the functional integrity of
the unit is compromised, do not start up the power tool. Instead, have it checked by a specialist workshop.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 652 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 652 in the language / languages: English as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Solo 652

Solo 652 User Manual - German - 24 pages

Solo 652 User Manual - Dutch - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info