658838
33
Zoom out
Zoom in
Previous page
1/46
Next page
Operating and maintenance information - Maintenance and care of the cutting gear
ENGLISH 33
E
N
G
Sharpening the saw chain
Just like any other cutting tool, the saw chain is subject to natural wear. Your chainsaw will only be
able to deliver its full potential if the saw chain is correctly sharpened.
Symptoms of a blunt saw chain or one which has been sharpened incorrectly:
o Poor cutting performance and floury chippings ! the saw chain is blunt.
o Chip size too small ! The depth limiter spacing is too small.
o Chip size too large and increased kickback tendency ! The depth limiter spacing is too large.
o Saw pulls to one side while cutting ! The saw chain is not evenly sharp.
o Visually apparent damage to the cutting surfaces.
Experience is needed to correctly sharpen the saw chain. If you are unsure, have the saw chain
checked by a specialist workshop and re-sharpened as required. The information provided below is
intended for experienced users or specialist workshops.
A special round chain file with the correct diameter should be used for sharpening. Normal round files
are not suitable.
Chain - code Pitch in inches Files Ø mm/inches Filing angle α Depth limiter spacing b mm/inches
21BP… .325’’ 4,8 /
3
/
16
30° 0,64 / .025
21LP... .325’’ 4,8 /
3
/
16
25° 0,64 / .025
73LP… 3/8’’ 5,5 /
7
/
32
25° 0,64 / .025
73D, DP… 3/8’’ 5,5 /
7
/
32
35° 0,64 / .025
Filing direction: 10° upw Filing direction: 0° horizon
21BP…, 21LP…,73LP… 73D, DP…
A file holder makes guidance of the file easier, as it has
markings for the correct sharpening angle (align the
markings parallel to the saw chain) and limits the
penetration depth (4/5 of the file diameter)
Position the file holder on the roof of the tooth. The file should only engage
during the forward stroke. Lift the file off when moving it back.
The shortest cutting tooth is sharpened first. The length of this tooth is then the
target size for all the other teeth on the saw chain. All of the cutting elements
must have the same length.
To start with, file all of the cutting elements on one side from the inside
outwards, then file all of the cutting elements on the other side.
Always fully file out any damage from the side plate or the roof of the tooth.
Correction of the depth limiter:
The distance b between the depth limiter (round nose) and the cutting edge defines
the thickness of the chips. The best cutting results are obtained with the prescribed
depth limiter spacing, which should be checked every time the saw chain is
sharpened.
Lay the depth limiter gauge on the cutting element. If the depth limiter protrudes,
file off the protruding part with a flat file.
Round off the front edge of the depth limiter. The original shape must be restored.
CAUTION: If the spacing is too large then there is a greater risk of
kickback.
For your safety: If you would like to pull the chain through while filing, pull the chain forwards
with a screwdriver towards the tip of the rail. This will reduce the risk of slipping.
α
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 651H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 651H in the language / languages: English as an attachment in your email.

The manual is 1,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info