658845

Solo 630 Manual

21
Zoom out
Zoom in
Previous page
1/72
Next page
21
– Step away as soon as the tree starts to fall. Observe the tree
crown and wait out the whipping of the tree crown. Never
continue to work under tangled branches or tree trunks.
BUCKING
Safety
- Position bucking spike firmly against tree trunk.
- Ensure firm and safe footing
Preparation (fig. 25)
- Before proceeding with the cut, clear work site of all foreign
objects such as sand, stones, nails etc. Such objects can cause
dangerous kick-back when struck.
– Ensure secure cutting support when cutting timber (preferable
a saw buck). Wood should never be held down by foot or by
another person.
– Wedge round logs to stop them from turning while cutting.
When cutting timber under tension or stress, always:
First make a relief cut into the pressure side. Exercise caution
because of possible bar pinching.
2. Next, carefully proceed with the cut into the tension side.
Note: Position cuts sideways when large logs are under strong
tension.
Fig. 26A = Trunk top under tension.
Danger: tree will arc upwards!
Fig. 26B = Trunk underside under tension.
Danger: Tree will slam downwards.
Fig. 26C = Large trunks and strong tension.
Danger: Trunk kicks away with immense speed and
power. Watch out for the root ball which may fall
backwards.
Fig. 26D = Trunk is under tension to the side.
Danger: Tree breaks out sideways
1 = Pressure Side
2 = Tension Side
Note: If trunk is under sideways tension, always position yourself
on the pressure side. Avoid pinching of the chain saw.
To avoid the wood splitting, make a relief cut. Make this cut
opposite the tension side, then finish by cutting from the tension
side (fig. 27).
If the saw is pinched in the cut, immediately shut off engine.
Move the position of the log or trunk with a pole or lever to
open cut and free the saw.
LIMBING
Basic Rules
The danger of kick-back is most prevalent during limbing.
- When limbing, rest your chain saw on the log as much as
possible. Do not cut with the bar nose – there is danger of kick-
back (fig. 28).
– Look out for branches under tension. Do not under cut free
hanging branches.
– Do not stand on the log while limbing.
– Remove any branches which pose an obstacle.
– Try not to be nervous or feel rushed while cutting.
– Use all opportunities to create favorable and elevated work
conditions (saw buck, work bench etc.).
– Always hold thumb of left hand under the handle bar.
When you change your position, always keep the
guide bar on the side of the tree opposite you
(fig. 29).
Always watch out for any movement of the trunk and the
branches be alert and cautious at all times.
When limbing strong deciduous wood, adhere to the following
operational sequence to avoid pinching of the saw:
1. Remove obstructing branches.
2. Cut off branches which are the cause of tension.
3. Cut main branch and watch pressure side 1 and tension side 2
(fig.30) (see section on ”limbing” – fig. 27).
SAFETY DURING START-UP OPERATIONS
- Ensure there are no children or other persons within the work
area. Also watch out for animals (fig.31).
- Start a chain saw only after it has been completely and correctly
assembled. As a rule, a chain saw should always be completely
assembled before being used!
- The bar cover (scabbard) must be removed first.
- Start the chain saw at a distance of at least 3 meters from where
the saw was fueled.
- Ensure safe and firm footing before starting the saw.
- When starting, support and hold the saw firmly. Ensure that
bar and chain are not within reach of any obstructions
(fig. 33 + 34).
Warning! The chain will run for some time after the
throttle is released to idle position. (idling effect).
STARTING
Cold engine starts (fig. 35)
Move ignition switch to position ‘I’ (A).
1. Pump fuel primer until it is
visibly filled with fuel and
resistance can be felt. (C).
1
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 630 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info