655623

Solo 462 Manual

21
Zoom out
Zoom in
Previous page
1/76
Next page
2 Preparing the device for use / 3 Mixing spraying agents and filling the spraying agent tank
ENGLISH 7
2 Preparing the device for use
2.1 Assembly
The pressure sprayer is dismantled before it is
dispatched. It must be fully reassembled again
before it is used.
Installation of the nozzle attachment
(only for models 461 and 462):
x Firmly screw the nozzle attachment (Fig. 2,
Pos. 1) with the O-Ring (10x2 mm) hand-tight
onto the spray tube. Do not use any tools!
Installation of the high-pressure hose:
x Push the threaded collar (Fig. 2, Pos. 2) onto the
high-pressure hose (Fig. 2, Pos. 3).
x Push the hose completely onto the provided
connector of the red-flanged housing, by using
strong pressure and turning the hose.
x Secure the hose by screwing on the threaded
collar (hand-tight, do not use any tools!).
Installation of the spray tube:
x Fasten the threaded collar (Fig. 2, Pos. 4) on
straight and firmly screw the spray tube (6) with
O-ring (16x3 mm) hand-tight onto the shut-off
valve. Do not use any tools!
When your work is completed, the spray tube
should be fitted into the holding clamp at the pump
handle (3).
Please put the nozzle completely up (Fig. 1).
Installation of the pressure gauge
(depending on the model):
x Unscrew the black threaded collar from the
shut-off valve.
x Screw the black threaded collar of the pressure
gauge accessory kit onto the shut-off valve.
x Insert the O-ring into the threaded collar and
screw the pressure gauge hand-tight into the
threaded collar. Do not use any tools!
2.2 Spray nozzle and filter element
At the factory, a red flat jet nozzle 04-F110 is
assembled as the standard spray nozzle.
Delivery rate: See section 10
A filter element is fitted in the elbow piece up-
stream of the spray nozzle (Fig. 2, within Pos. 1).
Only the spray nozzles listed in section 10 and the
genuine filter element (part no.: 40 74 922 25,
mesh aperture: 0.8 mm [0.031"]) must be used in
this pressure sprayer.
Changing spray nozzles and filter element:
See section 5.3
2.3 Carrying strap
Thread both ends of the carrying strap through the
slits provided on the red flanged housing (Fig. 4).
Use the sliding clip to adjust the carrying strap to
the required length.
2.4 Trial run
At first start-up, at the start of the spraying season
and in frequent use at least once a month, perform
a trial run according to section 5.1 to check the
entire device.
3 Mixing spraying agents and
filling the spraying agent tank
When handling the spraying agents, always
follow the safety instructions of these
operating instructions (pay special attention to
section 1.3) and the information provided by the
manufacturer of the particular spraying agent.
Before opening the spraying agent tank,
depressurise the device by pulling on the pressure
relief valve (Fig. 3).
Before pulling on the pressure relief valve (4), the
device must always be in an upright position.
Attention: Keep the device away from your face!
Spraying agent volume:
Mix the spraying agents according to the
instructions provided by the manufacturer of the
spraying agent. Choose the appropriate volume
according to requirements.
Mixing spraying agents:
Only mix spraying agents out in the open. Never do
this inside living spaces, stables or in storage
spaces that are used for food or animal feed.
Never mix the spraying agent directly in the
spraying agent tank.
Spraying agents in powder form:
x Mix the spraying agent in a separate container,
not in the spraying agent tank.
x Ensure that the mixture is thoroughly mixed
before pouring it into the spraying agent tank.
x Use the spray tube to thoroughly mix the
spraying agent in the tank.
Liquid spraying agents:
x Fill 1/4 of the spraying agent tank with clean
water.
x Then pre-mix the spraying agent with clean
water in a separate container according to the
instructions provided by the manufacturer of the
spraying agent.
x Pour the pre-mixed spraying agent into the
spraying agent tank.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solo 462 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solo 462 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info