Manual Solo 453 (page 18 of 72) (English, German, Dutch, French, Italian, Spanish)

655625

Zoom out

Zoom in

1/72

1 Safety regulations / 2 Preparing the device for use / 3 Mixing spraying agents and filling the spraying agent tank

ENGLISH 6

x Never smoke in areas where you are

working.

x When removing the spray tube, do not point to

yourself or other persons with the end of the

tube.

1.7 Maintenance, repairs and storage

Only perform maintenance work and repairs by

yourself if they are covered in these operating

instructions. All other work must be carried out by

an authorised workshop.

The repair of modern devices and their safety-

relevant assemblies, requires qualified, specialized

training and a workshop equipped with special

tools and test devices. The specialist has the

required training, experience, and equipment at his

disposal to provide you with the most cost-effective

solution and can help you in many ways with

advice and service.

x The device must not be serviced, repaired

or kept in the vicinity of naked flames.

x Before doing any maintenance work or repairs

and before opening the spraying agent tank,

depressurise the device by pulling on the

pressure relief valve (Fig. 4).

Before pulling on the pressure relief valve (2),

the device must always be in an upright position.

Attention: Keep the device away from your face!

x Always depressurise the device by pulling on the

pressure relief valve (2) before unscrewing the

high-pressure hose, the shut-off valve (5), the

pressure gauge (depending on the model), the

spray tube (1) and the nozzle attachment (4).

x All repairs must only be performed using SOLO

genuine replacement parts.

x The device must not be altered in any way, as

this could adversely affect the safety of the

device and potentially cause an accident or

injury.

2 Preparing the device for use

2.1 Assembly

The pressure sprayer is dismantled before it is

dispatched. It must be fully reassembled again

before it is used.

Installation of the spray tube (1):

x Fasten the threaded collar (Fig. 2, pos. 1) on

straight and firmly screw the spray tube with

O-ring (16x3 mm) hand-tight onto the shut-off

valve. Do not use any tools!

When your work is completed, the spray tube

should be fitted into the holding clamp (10) at the

transport handle (7) (Fig. 3).

Installation of the pressure gauge (depending on

the model):

x Unscrew the black threaded collar from the

shut-off valve.

x Screw the black threaded collar of the pressure

gauge accessory kit onto the shut-off valve.

x Insert the O-ring into the threaded collar and

screw the pressure gauge hand-tight into the

threaded collar. Do not use any tools!

2.2 Spray nozzle and filter element

At the factory, an adjustable spray nozzle is

assembled as the standard spray nozzle.

Delivery rate: See section 4.1

A filter element is fitted in the elbow piece

upstream of the spray nozzle (Fig. 2).

Only the above mentioned standard spray nozzle

(part no.: 49 00 525), the spray nozzles from the

nozzle kit (part no.: 49 00 574) and the genuine

filter element (part no.: 40 74 922 25, mesh

aperture: 0.8 mm [0.031"]) must be used in this

pressure sprayer. Changing spray nozzle and filter

element: See section 5.3

2.3 Height adjustment of the transport handle

In order to allow different sized people back-

friendly working, the height of the transport handle

is adjustable.

Height adjustment of the transport handle (7):

x Unscrew the handle screwing (8) by turning it to

the left (counterclockwise).

x Pull out the transport handle on both sides

evenly until the desired height is set.

x Re-tighten the handle screwing by turning it to

the right (clockwise).

2.4 Trial run

At the first start-up, at the start of the spraying

season and in frequent use at least once a month,

perform a trial run according to section 5.1 to check

the entire device.

3 Mixing spraying agents and

filling the spraying agent tank

When handling the spraying agents, always

follow the safety instructions of these

operating instructions (pay special attention to

section 1.3) and the information provided by the

manufacturer of the particular spraying agent.

Before opening the spraying agent tank,

depressurise the device by pulling on the pressure

relief valve (Fig. 4).

Before pulling on the pressure relief valve (2), the

device must always be in an upright position.

Attention: Keep the device away from your face!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Solo 453 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Solo 453 Manual

Product: