Manual Solis Futura (page 17 of 19) (English, German, French, Italian)

535612

Zoom out

Zoom in

1/19

INSTRUCTIONS FOR CLEANING

IMPORTANT: Always unplug the appliance

before cleaning the MAGIC VAC

– Carefully wash your hands before proceeding

to clean the appliance and its accessories.

– Both before and after use, clean the exposed

surfaces of the MAGIC VAC

using a sponge

moistened with a mild, non-abrasive dishwas-

hing detergent. If any liquids accidentally get

inside the appliance, do not connect it to the

mains electricity supply and do not use it;

contact your nearest dealer or authorised

service centre.

– The appliance is provided with a lower part (13)

which is entirely removable and washable also

on the dishwasher top rack (fig. S). Before was-

hing the lower part, remove both gasket (10)

(fig. T) and sealing gasket (11) (fig. U). Clean

both gaskets using a sponge moistened with a

mild washing up liquid and leave them to com-

pletely dry before positioning them again. Once

cleaning and drying are over, carefully fit both

gaskets back in their places. Then reinsert the

lower part (13) in the port provided on the lid

(5).

– Thoroughly wash the MAGIC VAC

accessories

(containers, caps, jars, etc.) like you would wash

any kitchen utensils, allowing them to

dry completely. If you wash the accessories

in a dishwasher, be sure to place them on

the top rack.

TROUBLESHOOTING

The MAGIC VAC

does not work

– Check the switch (1) position.

– Make sure the MAGIC VAC

has been plugged

in properly. Check the electric socket by plugging

another appliance into it.

– The MAGIC VAC

will stop automatically if

overheated. Allow it to cool down for 15 minutes

and try again.

– Check for faults in the power cord or the plug.

Should you detect a fault, do not use the

appliance.

The MAGIC VAC

fails to apply the first seal

on the bag cut from the roll

– Make sure the bag cut from the roll is

properly positioned as described in the para-

graph: „Making bags from MAGIC VAC

rolls“

The MAGIC VAC

does not create a complete

vacuum in the bags

– To seal the bag properly, you must make sure

that the open end remains completely inside the

Vacuum Chamber.

– Make sure that the Sealing Bar, the Sealing

Gaskets and Airtight Gaskets are free of impuri-

ties. After cleaning them, put them properly

back in place.

– The MAGIC VAC

bag might have a hole in it.

To check it, seal the bag with air on the inside.

Dip the bag in water and apply pressure. The

appearance of bubbles means that there is a

leak. Reseal or use another bag.

The MAGIC VAC

does not seal the bag

properly

– If the Sealing Bar overheats and melts the bag,

you may have to raise the Lid and allow the

Sealing Bar to cool down for a few minutes.

– The MAGIC VAC

is built in conformity with

current safety standards. Overheating will cause

it to turn off automatically. Allow the appliance

to cool down for 15 minutes and try again.

The MAGIC VAC

bag does not maintain a

vacuum after being sealed

– Leaks along the seam may be caused by creases,

crumbs, grease or liquids. Reopen the bag, clean

the upper inside part of the bag and remove

any foreign material from the Sealing Bar before

resealing it.

– Check that the bag has no holes in it which have

caused air to leak in. Use paper napkins to pro-

tect any sharp edges on the contents of the bag.

The MAGIC VAC

does not create a vacuum

in the containers

– By means of the Connection Hose, connect the

container lid (or the Cap Attachment if neces-

sary) to the Air Inlet of the appliance.

– Leave enough room (at least 3 cm) between the

contents and the top of the jar or container.

– If liquids come out during the vacuum-packing

process, remember that they must first be chilled

in a refrigerator, not left at room temperature.

– Check that the rim of the jar or container and

the universal lid are not damaged in the sealing

area. Wipe the rim and cap clean with a cloth

moistened with lukewarm water and repeat the

vacuum-packing process.

– Make sure that the gasket of the container cap

or the universal cap is set properly in place and

is not damaged.

MAGIC VAC

Executive

containers or

MAGIC VAC

Universal Caps do not maintain

a vacuum

– Make sure that the arrow on the knob of the

container cap is positioned on „VACUUM“

before creating a vacuum in the container and

it is positioned on „CLOSED“ after a vacuum

is formed.

– Make sure that the O-ring beneath the knob

of the container cap or the universal cap is set

properly in place.

MAGIC VAC

Family

containers do not

maintain a vacuum

– Make sure that the gasket beneath the central

button (17) of the container cap is set properly

in place and is not damaged.

packing cycle and turn off automatically on its

completion.

– Disconnect the hose from both the Bottle Cap

and the appliance immediately.

– To open a bottle sealed with the MAGIC VAC

Bottle Cap, simply pull the cap out of the bot-

tle. You will hear the air rushing into the bottle.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Solis Futura in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Solis Futura Manual

Product: