535738

Solis Exclusive Manual

33
Zoom out
Zoom in
Previous page
1/36
Next page
33
E
TROUBLESHOOTING
The MAGIC VAC
®
does not work
–
Check the switch (1) position.
– Make sure the MAGIC VAC
®
has been plugged
in properly. Check the electric socket by plugging
another appliance into it.
– The MAGIC VAC
®
will stop automatically
if overheated. Allow it to cool down for
15 minutes and try again.
–
Check for faults in the power cord or the
plug. Should you detect a fault, do not use the
appliance.
The MAGIC VAC
®
fails to apply the first
seal on the bag cut from the roll
– Make sure the bag cut from the roll is proper
-
ly positioned as described in the paragraph:
„Making bags from MAGIC VAC
®
rolls“
The MAGIC VAC
®
does not create a
complete vacuum in the bags
– To seal the bag properly, you must make sure
that the open end remains completely inside
the Vacuum Chamber.
– Make sure that the Sealing Bar, the Sealing
Gaskets and Airtight Gaskets are free of
impurities. After cleaning them, put them
properly back in place.
– The MAGIC VAC
®
bag might have a hole in it.
To check the bag, seal it with air inside, place
it underwater and apply pressure on it.
The appearance of bubbles means that there
is a leak. Reseal or use another bag.
The MAGIC VAC
®
does not seal the bag
properly
–
Whenever the machine does not seal the bag
completely, press the TIME SEAL knob
(6) and
increase sealing time.
– If the Sealing Bar overheats and melts the bag,
you may have to raise the Lid and allow the
Sealing Bar to cool down for a few minutes.
– The MAGIC VAC
®
is built in conformity with
current safety standards. Overheating will cause
it to turn off automatically. Allow the appliance
to cool down for 15 minutes and try again.
The MAGIC VAC
®
bag does not maintain a
vacuum after being sealed
– Leaks along the seam may be caused by creases,
crumbs, grease or liquids. Reopen the bag, clean
the upper inside part of the bag and remove
any foreign material from the Sealing Bar before
resealing it.
–
Check that the bag has no holes in it which
have caused air to leak in. Use paper napkins to
protect any sharp edges on the contents of the
bag.
The MAGIC VAC
®
does not create a vacuum
in the containers
– By means of the Connection Hose, connect
the container lid (or the Cap Attachment if
necessary) to the Air Inlet of the appliance.
–
Leave enough room (at least 3 cm) between the
contents and the top of the jar or container.
– If liquids come out during the vacuum-packing
process, remember that they must first be chilled
in a refrigerator, not left at room temperature.
–
Check that the rim of the jar or container and
the universal lid are not damaged in the sealing
area. Wipe the rim and cap clean with a cloth
moistened with lukewarm water and repeat the
vacuum-packing process.
– Make sure that the gasket of the container cap
or the universal cap is set properly in place and is
not damaged.
MAGIC VAC
®
Executive containers or
MAGIC VAC
®
Universal Caps do not maintain
a vacuum
– Make sure that the arrow on the knob of the
container cap is positioned on „VACUUM“
before creating a vacuum in the container and
it is positioned on „CLOSED“ after a vacuum is
formed.
– Make sure that the O-ring beneath the knob
of the container cap or the universal cap is set
properly in place.
MAGIC VAC
®
Family containers do not
maintain a vacuum
– Make sure that the gasket beneath the central
button (21) of the container cap is set properly
in place and is not damaged.
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solis Exclusive at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solis Exclusive in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info