799214
12
Zoom out
Zoom in
Previous page
1/32
Next page
Winding the bobbin
- 1. Put a spool of thread on spool pin. (Fig.20)
- 2. Guide the thread through the bobbin winder tension disk on the
upper side of the machine. (Fig.21)
- 3. Put the bobbin on the bobbin winder pin, wind thread clockwise
around bobbin several times. (Fig. 22)
- 4. Push bobbin to the left. (Fig.23)
- 5. Switch on the machine to start winding. (Fig.24)
- 󰀨
thread you wanted had winded on bobbin.
- 󰀨
and cut the thread. (Fig.25)
Caution
- During bobbin winding, no thread on the needle/take up lever is al-
󰀨
- Before bobbin winding, raise the presser foot.
Adjusting stitching
- 1. As shown in the picture A, normal stitching shall have top and bot-
tom threading evenly, neither over tight nor loose.
- 2. If the bottom threading looks like a straight line (Fig.B), which indi-
cates the top thread is too loose. Please turn upper thread tension dial
to direction with bigger number to increase pressure until the stitching
return to norma.
- 3. If the top thread looks like straight line (Fig.C), which indicates an
over-tight top thread. Please turn the upper thread tension dial to the
direction with smaller number to reduce pressure until the stitching
back to normal.
Other functions
Overlocked
󰀨
- We must select an overlock or overlock stitch, 5 or 6 leaving the width
and length values that come by default. (depending on the machine
they will be one or the other)
- Advancing slowly, the fabric that we have left, while the needle is

󰀨
Pre-riveted drilling
- It consists of moving the needle without thread front and back to pierce
the fabric and thus be able to put a brooch or a rivet.
- If you want a bigger hole you should change the needle to a thicker
one.
Applicable cloth for sewing
Cloth
Sewing
presentation
Cotton /
Linen
Silk /
Wool
Polyester Elastic
-
cation
Regular
Thick
Thin
Hard
Soft
󰀨

󰀩

Note:


Thick (fabric): two layers of the fabric thickness >0.8mm



If the cloth, which size is “100mmx30mm”, is extending to or
over 106 mm under 0.5Kg tension force, then the cloth is de-


4. Soft fabric: such as towel, duster, etc.

- 󰀨󰀨
- 󰀨
- Unplug the appliance from the mains.
- Put the cable back in the cable housing.
- Clean the appliance.
Carry handle/s:
- This appliance has a handle on the upper part of the body, which facili-
tates comfortable transportation.
Safety thermal protector:
- The appliance has a safety device, which protects the appliance from
overheating.
- 󰀨
disconnect it from the mains supply, and wait for approximately 15
minutes before reconnecting. If the machine does not start again seek
authorised technical assistance.
CLEANING
- Disconnect the appliance from the mains and allow it to cool before
undertaking any cleaning task.
- Clean the equipment with a damp cloth with a few drops of washing-up
liquid and then dry.
- Do not use solvents, or products with an acid or base pH such as
bleach, or abrasive products, for cleaning the appliance.
- Do not let water or any other liquid get into the air vents to avoid dam-
age to the inner parts of the appliance.
- Never submerge the appliance in water or any other liquid or place it
under running water.
Supplies
- Supplies can be acquired from distributors and authorised establish-

- Only the following type of supplies must be used with the appliance.
- Lamp type: E14, Max: 15 W
- These supplies are available in specialist shops.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solac SW8231 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solac SW8231 in the language / languages: English, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2.88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info