Manual Solac SW8230 - Cotton 16.0 (page 13 of 24) (English, French, Portuguese, Spanish)

718539

Zoom out

Zoom in

1/24

liquid and then dry.

- Do not use solvents, or products with an acid or base pH such as

bleach, or abrasive products, for cleaning the appliance.

- Do not let water or any other liquid get into the air vents to avoid dam-

age to the inner parts of the appliance.

- Never submerge the appliance in water or any other liquid or place it

under running water.

Supplies

- Supplies can be acquired from distributors and authorised establish-

ments (such as lters, etc.) for your appliance model.

- Only the following type of supplies must be used with the appliance.

- Lamp type: E14, Max: 15 W

- These supplies are available in specialist shops.

Anomalies and repair

- In case of breakdown call the customer, service telephone number

indicated in the guarantee sheet. Do not attempt to disassemble or

repair the appliance yourself as this may be dangerous.

For EU product versions and/or in case that it is requested in your

country:

Ecology and recyclability of the product

- The materials of which the packaging of this appliance consists are

included in a collection, classication and recycling system. Should

you wish to dispose of them, use the appropriate public recycling bins

for each type of material.

- The product does not contain concentrations of substances that could

be considered harmful to the environment.

This symbol means that in case you wish to dispose of the

product once its working life has ended, take it to an authorised

waste agent for the selective collection of Waste from Electric

and Electronic Equipment (WEEE).

This appliance complies with Directive 2014/35/EU on Low Voltage, Di-

rective 2014/30/EU on Electromagnetic Compatibility, Directive 2011/65/

EU on the restrictions of the use of certain hazardous substances in

electrical and electronic equipment and Directive 2009/125/EC on the

ecodesign requirements for energy-related products.

TROUBLESHOOTING:

Problem Reason Solution

No pow-

er or the

machine

runs

slowly

Adapter power is not

properly connected

Correct connect adaptor.

Replace with a new adaptor

Skipping

stitches

Needle eye not in the

middle

Remove and re-insert the

needle with the at side of the

needle to the back.

Needle bent

Remove and re-insert a new

needle.

Presser foot too loose

Tighten the presser foot ac-

cording to installation instruc-

tion above mentioned.

Bobbin

thread

cannot

be drawn

Lower thread has been

used up

Replace with new full bobbin

Needle threaded

incorrectly

Re-thread the needle, making

sure it is threaded from the

front to the back.

Thread

keeps

breaking

Thread blocked by

lower bobbin

Correctly thread the upper

thread and lower thread again

according to instruction above

mentioned.

Needle scarf too rough

Remove and re-insert a new

needle.

Needle shank not seat-

ed in the upper end

Insert the needle correctly

Thread tension dial,

thread guide or thread

pulling bar is rough

Polish with ne sand paper

Stitch-

es too

loose or

uneven

Thread blocked by

upper bobbin spool

Pull out the spool pin and

make the bobbin or thread run

smoothly

Upper thread too loose

or tight

Adjust thread tension dial and

make the stitches sew evenly

Needle bent

Remove and re-insert a new

needle

Threading incorrect Check and thread again

Needle

breaks

Presser foot and/or

needle is loose

Remove and re-insert a new

needle, and tightly x presser

foot and needle

Pull fabric with force

when sewing

Remove and re-insert a new

needle and tightly x it. After

that thread machine, again.

Needle not lowered

into fabric when start

sewing

Remove and re-insert a new

needle and tightly x it, thread

again, turn the hand wheel to

lower the needle into fabric,

and then start sewing

Remove and re-insert a new

needle and tightly x it

The needle is in the

fabric when adjust the

pattern selection dial

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Solac SW8230 - Cotton 16.0 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Solac SW8230 - Cotton 16.0 Manual

Product: