Manual Solac DC7502 (page 9 of 62) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

719065

Zoom out

Zoom in

1/62

• Do not touch the appliance with wet hands when in

operation.

• Do not use the appliance on wet surfaces or

outdoors.

• The appliance must be connected to a power socket

with a suitable ground connection.

• Do not use on sensitive areas such as eyebrows,

moles, warts, open wounds, cuts, burns, etc.

• People insensitive to heat must be careful when they

use the device.

• Never use the appliance without wax. The device

is designed to melt and heat depilatory wax,

whether empty pot heats the device may be

damaged.

•Do not use with the lid on. The lid is designed to

prevent the accumulation of dust when the

machine is not being used. Melt wax with the lid

on, may cause damage to the device.

2 MAIN COMPONENTS

1 Lid

2 Filter (removable).

3 tub 1

4 tub 2

5 light .

6 temperature regulation controls.

7 Spatula

3 OPERATION

Use this appliance to remove hair from the

desired areas of the body. It is not advisable to remove

hair from the armpits and eyebrows at home. This

treatment should be left to a beautician.

Hot wax hair removal has the advantage of

reducing the rate of hair growth.

To obtain an excellent result, hair should be at

least 2 to 3 millimetres in length and skin should be

clean without cream or talc.

1 Plug in the appliance.

2 Remove lid and pour the capsules of wax into tub 1

(approx. 200 gr.).

3 Set the tub's temperature regulator to wax melting

mode (Fig. 1).

The light will then come on.

The temperature regulator of vat 2 will be in the

"stop" setting (Fig. 2).

4 Stir the wax now and again with the spatula.

5 When it has taken on the consistency of a thick

syrup. re-adjust the temperature regulator to hair

removal setting (Fig. 3). The light will go out.

After a few minutes the light will come on again

and the wax should be at a suitable temperature for

hair removal.

6 Mix the wax to ensure an even temperature

throughout.

7 Using the spatula place a little wax on the back of

your hand to test the temperature. If this is suitable for

you. you may begin hair removal.

Thanks to the thermostat, the temperature of the

wax will remain constant.

8 Run your hand along your legs using an upward

motion to flatten out the hairs.

9 Using the large spatula, spread out the wax in strips

of approximately 6 cm in length and 3 cm in width.

Wax should always be applied in the opposite

direction to the growth of the hair.

10 Removing the wax

• Wait for 30 to 60 seconds until the wax strip

becomes dry to the touch.

• Hold your skin taut. Grasp the thicker end of the

wax, and pull the strip back as quickly as you can,

against the direction the hair grows (from ankle to

knee). Pull the strip back on itself, close to the skin

rather than away from it. (Fig. 4)

• To soothe the skin immediately after you remove the

strip, press the area with your hand.

• Use some used wax or oil to remove wax traces. This

wax doesn’t come out with water, soap or alcohol.

(Fig. 4)

11 Place the strips of used wax in the filter in tub 2

and set tub 2’s temperature regulator to wax melting

mode (Fig. 1).

12 When the wax has melted, filter it, clean, then

remove the filter and place it under cold water.

13 If necessary, put back the temperature regulator to

the hair removal setting (Fig. 3).

You may continue hair removal by using the

wax in tub 2, then placing the used strips in the filter

which you have now placed into tub 1.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Solac DC7502 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 6,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Solac DC7502 Manual

Product: