488728

Solac AS3260 Manual

13
Zoom out
Zoom in
Previous page
1/78
Next page
CLEANING AND CONSERVATION 13
en
SAFETY THERMOSTAT
The system has a safety thermostat. If for any reason the vacuum cleaner should overheat,
the thermostat will automatically shut off the appliance. If this should happen:
1 Press the on/off switch (5) and unplug the appliance from the mains.
2 Check that the air intakes and outlets are not blocked. If they are blocked, get rid of
the cause of the blockage.
3 Empty the dust container (outer and inner chamber). See the next section “Cleaning
and Conservation”.
) If the automatic shut-off was due to the motor overheating, wait for about one hour for
the appliance to cool before turning it on again. You can reduce the waiting time by
placing the appliance in a cool or well-ventilated place to allow the heat to dissipate.
CLEANING AND CONSERVATION
EMPTYING THE DUST CONTAINER (19)
) The dust container (19) has a maximum level mark. Check the dust does not exceed
that level.
1 Turn the carry handle (15) backwards to make the dust container (19) accessible.
2 Press the release button (24). This releases the dust container. (fig. 4).
3 Remove the dust container and hold it over the waste bin. Press the button (23) on the
container (fig. 5) to empty the contents into the bin.
4 Turn the dust container cover (21) anti-clockwise and remove the inner chamber (20)
(fig. 6). Empty the contents.
5 Clean the inner chamber (20) and dust container with a brush and wet cloth.
) Check that the washed elements are completely dry before putting them back
together.
) Never immerse the inner chamber in water or any other liquid, nor put it in the
dishwasher. Do not use abrasive products or solvents.
6 Put the inner chamber back into the container (check that the marks coincide).
7 Place the container cover (21) on the mark and turn it clockwise to the mark .
8 Put the dust container back inside the appliance. Push the container towards the
appliance body while pressing the release button (24). This blocks the container.
CLEANING THE MOTOR PROTECTION FILTER (26)
) It is advisable to inspect the motor protection filter from time to time, to ensure that it is
operating correctly.
) Once or twice a year, or if a reduction in suction power is detected, clean the protection
filter. To do so:
1 Remove the dust container. See the previous section “Emptying the dust container
(19)”.
2 Remove the filter cover (25) by pressing the upper tab. Remove the grille (27) (fig. 7).
3 Remove the protection filter (26) from the grille (27) (fig. 7).
4 Wash the filter with tap water and leave it to dry completely.
) The filter can be washed with warm water (max. 40 ºC). Leave it to dry for 24 hours
before replacing it.
5 Put the grille and motor protection filter back in their housing.
) Never use the vacuum cleaner without the motor protection filter.
AS3260.book Page 13 Thursday, January 14, 2010 1:29 PM
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Solac AS3260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Solac AS3260 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info