798252
12
Zoom out
Zoom in
Previous page
1/40
Next page
PARTS DESCRIPTION
BEFORE USING FOR THE FIRST TIME
Please check all packaging material
carefully before discarding. Many
accessory parts are contained within the
packaging material.
Assemble the motor to the base; place
narrow end of motor into the opening in the
seated in the base. If desired for storage,
the motor can be removed from the base.
Hand-wash the cup holder, exterior bowl,
and auger in warm, soapy water. Rinse and
dry thoroughly. Do not wash any parts in a
dishwasher. CAUTION: The exterior bowl
contains a sharp shaving blade, handle
with care.
NEVER IMMERSE THE MOTOR IN
WATER OR ANY OTHER LIQUID.
USING YOUR ELECTRIC ICE SHAVER
1. If using paper cone cups, push cup holder
into opening on front of ice shaver housing.
If using regular cups, do not attach cup
holder.
2. Slide the gear ring over the auger and snap
in place. You will hear a click when it is fully
engaged.
3. Place the auger with gear ring inside the
exterior bowl. Lock the auger in place with
the securing nut by turning nut clockwise.
4. Line up the two outside tabs of the exterior
bowl assembly with the matching grooves
on the Ice Shaver Housing. Push gently in
place to secure.
CAUTION: The exterior bowl contains a
sharp shaving blade, handle with care.
5. Place paper cone cups in cup holder. If
using regular cups, place cup under the
shaving blade on the drip tray.
6. Add ice cubes to auger.
7. Plug the Ice Shaver into a 220 240 volt,
AC electric outlet only.
8. Place the lid on top of the exterior bowl,
aligning the tabs. Turn the lid counter
clockwise until the lid tab engages the
interlock switch. The motor will start and the
ice will begin shaving.
9. To stop shaving ice, turn the lid clockwise to
disengage the motor switch.
10. Unplug from power supply immediately
after use. Note: There will always be a small
amount of ice remaining in the auger after
shaving. Discard the remaining ice.
CAUTION: Do not run ice shaver
continuously for longer than 5 minutes as
overheating may occur. Allow motor to cool
down before repeat usage.
A small amount of smoke and/or odour
may occur upon use due to the release of
manufacturing oils – this is normal.
Some minor expansion/contraction sounds
may occur during use – this is normal.
CLEANING YOUR ELECTRIC ICE SHAVER
1. Always unplug appliance before cleaning.
2. Hand wash parts in warm, soapy water.
Rinse and dry thoroughly.
CAUTION: Be extremely careful of shaving
blade in exterior bowl as blade is very sharp.
Note: Do not wash parts in a dishwasher.
3. Clean exterior of the appliance with a damp,
soft cloth and wipe dry.
Note: Do not immerse motor housing in
water or other liquid.
NEVER ATTEMPT TO SHARPEN
SHAVING BLADE AS INJURY MAY
OCCUR.
This appliance has no user serviceable
parts.
HELPFUL HINTS
Be sure you have an adequate supply of ice
cubes.
If your motor is labouring or if you get poor
shaving results, soften your ice cubes. This
can be done by letting your ice sit at room
temperature for a few minutes, or running
DO NOT
Cube shaped ice performs better than the
half-moon shaped ice from ice makers or
round cubes from store-bought bagged
ice.
Lid
Gear
Ring
Exterior
Bowl
Removable
Cup Holder Base
Motor
Auger
Securing Nut
11 español english français portuguese deutsch italiano
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sogo SS-5272 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sogo SS-5272 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info