682824
34
Zoom out
Zoom in
Previous page
1/41
Next page
34
ALARM ID
DESCRIPTION
USER ACTION
AF:01
The water does not heat to
temperature in the set time.
User: run the DEFAULT PROCEDURE described above. If the
alarm does not reset, run the RESET PROCEDURE.
AF:05
Operating temperature sensor
TL1 has generated an
anomalous signal (sensor
"open").
User: run the DEFAULT PROCEDURE described above. If the
alarm does not reset, run the RESET PROCEDURE.
AF:07
Drying temperature sensor TA1
has generated an anomalous
signal (sensor "open").
User: run the DEFAULT PROCEDURE described above. If the
alarm does not reset, run the RESET PROCEDURE.
AF:09
Partial draining has not been
successful.
User: run the DEFAULT PROCEDURE described above. If the
alarm does not reset, run the RESET PROCEDURE.
AF:11
No cold water during the fill
cycle.
Check the water supply:
1. Check that the intake tap is open.
2. Check the water supply pressure.
3. Check the position of the intake hoses.
Run the DEFAULT PROCEDURE described above. If the alarm
does not reset, run the RESET PROCEDURE.
AF:12
No hot water.
Check the hot water supply:
1. Check that the intake tap is open.
2. Check the water supply pressure.
3. Check the position of the intake hoses.
Run the DEFAULT PROCEDURE described above. If the alarm
does not reset, run the RESET PROCEDURE.
AF:17
Cold water filling time not
correct.
Run the checks and procedures specified in AF:11.
AF:18
Hot water filling time too long.
The machine is taking too long
to fill with hot water.
Run the checks and procedures specified in AF:12.
AF:23
Not enough water. wash
chamber water level is
dropping.
Run the checks and procedures specified in AF:11.
Also check for leaks - check for water on the floor around the
machine.
If you find any leaks: immediately close all supply taps and
contact technical service.
AF:25
Water circuit malfunction.
User: run the DEFAULT PROCEDURE described above. If the
alarm does not reset, run the RESET PROCEDURE.
Then open the door and check that there is not too much
foam in the wash chamber (reduce the amount of rinse aid)
and that the wash chamber filter is clean (proceed as shown
in fig. 16).
AF:29
The wash chamber does not
drain in the set time.
Check the drain connection,
in particular that the height of the drain fittings meets the
specifications given, and check for kinks and restrictions
along the drain hose.
Check that the filter unit is clean fig. 16
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smeg SWT262TD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smeg SWT262TD in the language / languages: English as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smeg SWT262TD

Smeg SWT262TD User Manual - German - 44 pages

Smeg SWT262TD User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info