ESPAÑOLInstalaciónPágina44Instrucciones de usoPágina46
PORTUGUÊSInstalaçãoPágina53Instruções de utilizaçãoPágina55
ITALIANOInstallazionePagina62Istruzioni per l’usoPagina64
SVENSKA InstallationSidan71Bruksanvisning Sidan73
DANSKInstallationSide80BrugervejledningSide82
РУССКИЙУстановкаСтраница89Инструкции по пользованию приборомСтраница91
POLSKIInstalacjaStrona
98
Instrukcja obsługiStrona
100
ΔϳΑέόϟ
ΏϳϛέΗ
ΔΣϔλϟ
˼
ΕΎϣϳϠόΗϝΎϣόΗγϻ
ΔΣϔλϟ
˾
4
483 mm
553 mm
30 mm
+1
0
580
650
700 mm
510 mm
52 mm
A
R = Min. 6,5 mm
Max. 8 mm
490 mm
560 mm
0
+2
0
+2
Min. 50 mm
5
12
3
Min. 5 mm
Min. 10 cm
Min. 3 cm
Max. 6 cm
Min. 5 mm
X 4
EN6
YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT
This manual and the appliance itself provide important safety messages, to be read and always observed.
All messages relevant to safety specify the potential risk to which they refer and indicate how to reduce the risk of injury,
damage and electric shocks due to incorrect use of the appliance. Make sure to comply with the following:
-Use protective gloves to perform all unpacking and installation operations.
-The appliance must be disconnected from the power supply before carrying out any installation operation.
-Installation and maintenance must be carried out by a specialised technician, in compliance with the manufacturer’s
instructions and the local safety regulations in force. Do not repair or replace any part of the appliance unless
specifically stated in the user manual.
-The appliance must be earthed.
-The power cable must be long enough for connecting the appliance, fitted in the cabinet, to the power supply.
-For installation to comply with the current safety regulations, an omnipolar switch with minimum contact gap of
3mm is required.
-Do not use multi-sockets or extension cords.
-Do not pull the appliance’s power cable.
-The electrical parts must not be accessible to the user after installation.
-The appliance is designed solely for domestic use for cooking food. No other use is permitted (e.g. heating rooms).
The Manufacturer declines any liability for inappropriate use or incorrect setting of the controls.
-The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating
elements. Very young (0-3 years) and young children (3-8 years) shall be kept away unless continuously supervised.
-Children from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge can use this appliance only if they are supervised or have been given instructions on safe
appliance use and if they understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
-Do not touch the appliance heating elements during and after use. Do not allow the appliance to come into contact
with cloths or other flammable materials until all the components have cooled down completely.
-Do not place flammable materials on or near the appliance.
-Overheated oils and fats catch fire easily. Pay attention when cooking food products rich in fat and oil.
-A separator panel (not supplied) must be installed in the compartment under the appliance.
-If the surface is cracked, switch off the appliance to avoid the possibility of electric shock (only for appliances with
glass surface).
-The appliance is not intended to be operated by means of an external timer or separate remote control system.
-Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire
with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.
Danger of fire: do not store items on the cooking surfaces.
-Do not use steam cleaners.
IMPORTANT SAFETY INSTRUCTIONS
This is the danger symbol, regarding safety, warning of potential risks to users and others.
All safety messages will be preceded by the danger symbol and the following words:
DANGER
Indicates a hazardous situation which, if not avoided, will result in serious
injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious
injury.
ENGLISHInstallationPage4Instructions for usePage
EN8
After unpacking the product, check for any damage during transport. In case of problems, contact the dealer or the After-Sales Service.
For built-in dimensions and installation instruction, see the pictures in page 2.
PREPARING THE CABINET FOR FITTING
INSTALLATION
WARNING
-Install a separator panel under
the hob.
-The lower part of the product
must not be accessible after
installation.
-Do not fit the separator panel if
an undertop oven is installed.
•The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure.
•In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. 5 mm).
•If an undertop oven is installed, make sure the oven is equipped with a cooling system.
•Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them.
•To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of the appliance.
min. 5 mm
min. 20 mm
min. 5 mm
EN9
Connect to terminal Block
For the electrical connection a power cord ( 5x2,5 mm ) is present in the supply. To connect to the terminal block, follow the instuction below:
•Secure the power cable with the cable clamp.
•Remove the terminal cover (A) by unscrewing the screw and insert the cover into the hinge (B) of the terminal.
•Close the cover (C) and screw on the terminal with the screw removed.
Connect to wall side
ELECTRICAL CONNECTION
WARNING
-Disconnect the appliance from the power supply.
-Installation must be carried out by qualified personnel who know the current safety and
installation regulations.
-The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations
provided in this chapter.
-The power cable must be long enough to allow the hob to be removed from the worktop.
-Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home.
Remove shunts from terminal block
Before power cord connection remove the two shunts as per picture
Connecting to the terminal block
For 220-240V 1N use the cord paired as supplied.For 380-415V 3N or 380-415V 2N, separate with the scissors the wires as showed in the image below and
connect them
L1=R BLACK L2=S BROWN =E YELLOW-GREEN
N1=N BLUE N2=N GREY with blue film
EN10
Control Panel Description
Control panel
Switching the hob ON/OFF
To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up. To switch off, press the same button until the displays switch
off. All the cooking zones are deactivated
If the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled down.
If within 10 seconds of switching on, no function is selected, the hob switches off automatically.
Switching on and adjusting cooking zones
After switching the hob on, activate the required cooking zone by pressing the corresponding circular button and place the pot on the zone. With the Slider control it
is possible to select the required power level, from min. 0 to max. 9, or booster “P” if available.
To increase the power level, slide your finger on the slider from left to right several times; to decrease it, slide in the opposite direction. Alternatively the “+” and “-”
quick access buttons can be used.
Deactivation of cooking zones
To switch off the cooking zone, press the corresponding button for more than 3 seconds.
The cooking zone switches off and, if still hot, the letter “H” appears on the zone display.
INSTRUCTIONS FOR USE
Control panel lock
Cooking zone controls and corresponding display
On/Off
Multizone
Quick access
Slider
Multizone
Power management/Timer/
Lock function button
Power indicator display
Selected cooking zone indication
Cooking zone positioning
Slider operation
Increase power level
Decrease power level
EN11
Control panel lock
This function locks the controls to prevent accidental activation of the hob. To activate the control panel lock, switch the hob on and press the Timer button for three seconds; an
acoustic signal and a luminous indicator near the padlock symbol signal activation. The control panel is locked except for the switching off function. To deactivate the control lock,
repeat the activation procedure. The luminous dot goes off and the hob is active again.
The presence of water, liquid spilled from pots or any objects resting on the button below the symbol can accidentally activate or deactivate the control panel lock.
Timer
The timer can be used to set the cooking time for a maximum of 99 minutes (1 hour and 39 minutes) for all the cooking zones.
Select the cooking zone to be used with the timer, press the timer and a beep signals the function (see figure). The display shows “00” and the LED
indication comes on. The Timer value can be decreased and increased by keeping the slider function “+” and “-” buttons pressed. When the set time
has elapsed, an acoustic signal sounds and the cooking zone switches off automatically. To deactivate the timer, keep the Timer button pressed for at
least 3 seconds.
To set the timer for another zone, repeat the above steps. The timer display always shows the timer for the selected zone or the shortest timer.
To modify or deactivate the timer, press the cooking zone selection button for the timer in question.
Control panel warnings.
Residual heat indicator.
The hob is fitted with a residual heat indicator for each cooking zone. These indicators alert the user when cooking zones are still hot.
If the display shows , the cooking zone is still hot. If the residual heat indicator of a given cooking zone is lit, that zone can be used, for example, to keep a
dish warm or to melt butter.
When the cooking zone cools down, the display goes off.
Incorrect or missing pot indicator.
If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions for your induction hob, the message “no pot” will
appear in the display (see figure at side). If no pot is detected within 60 seconds, the hob switches off.
Fast boil function (Booster)
This function, only present on some cooking zones, makes it possible to exploit the hob’s maximum power (for example to bring water to the boil very quickly).
To activate the function, press the “+” button until “P” appears on the display. After 10 minutes’ use of the booster function, the appliance automatically sets the
zone to level 9.
“Power management” (Function where it is available)
Thanks to the “Power management” function, the user can set the maximum power the hob can reach, as required.
This setting is possible at any time and is maintained until the next change.
By setting the required maximum power, the hob automatically adjusts distribution in the various cooking zones, ensuring that this limit is never exceeded; with the
advantage of also being able to manage all the zones simultaneously, but without overload problems.
4 maximum power levels are available and showed on display: 2.5 – 4.0 – 6.0 – 7.2 kW (7.2 kW is considered as max power of cooktop)
At the time of purchase, the hob is set to maximum power
After plugging the appliance into the electrical socket, in the first 60 seconds it is possible to set the required power level by running the following points:
In case of an error when setting the power, the symbol appears in the middle and an acoustic signal sounds for about 5 seconds. In this case repeat the
configuration procedure from the beginning. If the error occurs again, contact the After-Sales Service.
During normal use, if the user tries to increase the maximum available power level when reached, the level of the zone in use flashes twice and an acoustic signal
sounds.
To obtain a higher power in that zone, it is necessary to manually decrease the power level of one or more already active cooking zones.
StepControl panelDisplay
1Press for approximately
3 seconds
2Press the Power
Management button to
confirm the previous step
The display shows
3
/
Press to set the chosen level
amongst the different
options available
The light comes on together with the in-use
lights for the individual cooking zones
4Press the Power
Management button to
confirm the previous step
The display shows the set level which flashes
for approximately 2 seconds; after which the
hob emits an acoustic signal and then turns
itself off; it is now ready for use
EN12
Multizone
Where present, this function allows the cooking zone to be used as two separate zones or as a single extra large zone.
It is perfect for oval, rectangular and elongated pans (with maximum base dimensions of 38x23 cm) or more than one standard pan in the same time. In order to activate
the Multizone, switch on the hob, press simultaneously the 2 selecting buttons of the zones as shown in the picture below: the two cooking zone displays show level
“0”; both dots next to the level number are lit, indicating that the Multizone is activated.
To change the power level (from 1 to max. 9 or P) press the -/+ buttons or slide your finger horizontally on the slider. To deactivate the Multizone, press simultaneously
the 2 selecting buttons of the zones. To switch off the zones instantly, hold one of the zone selection button for 3 seconds.
The message “no pot” will appear on the display of the zone that is not able to detect any pot (because of missing pot, or misplaced or not suitable for
induction hob). This message remains active for 60 seconds: in this time you can add or slide pots within the Multizone area as you prefer.
After 60 seconds if no pan is placed on the zone, the system stops “searching” pots on that zone, the symbol remains visible on the display to remind that the zone
is disabled.
To reactivate the Multizone, press one of the 2 buttons or
The Multizone is also able to detect when a pot is moved from one zone to the other one within the Multizone area keeping the same power level of the zone where
the pan originally was placed (see the example in the figure below: if the pot is moved from the front heater to the rear heater, the power level will be shown on the
display corresponding to the zone where the pot is placed).
It is also possible to operate the Multizone as two independent cooking zones, using the corresponding button of the single zone. Place the pot in the center of the
single zone and adjust the power level with the slide touchscreen.
Important: make sure to place the pans centered on the cooking zone in the way to cover the logo placed in the center of the single cooking zone.
In case of big pot, oval, rectangular and elongated pans make sure to place the pans centered on the cooking zone covering both logos.
Examples of good pot placement and bad pot placement :
i
i
EN13
IMPORTANT: Do not use abrasive sponges or scouring pads. Their use could eventually ruin the glass.
•After each use, clean the hob (when it is cool) to remove any deposits and stains due to food residuals.
•Sugar or foods with a high sugar content damage the hob and must be immediately removed.
•Salt, sugar and sand could scratch the glass surface.
•Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer’s instructions).
•Read and follow the instructions given in the section “Instructions for use”.
•Check that the electricity supply has not been shut off.
•Dry the hob thoroughly after cleaning it.
•If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions.
•If the hob cannot be switched off after using it, disconnect it from the power supply.
Induction hobs can make whistling or crackling sounds during normal operation, these actually come from the pots and pans as a result of the characteristics of the
bottoms (for example, bottoms made of several layers of material, or uneven bottoms). These noises vary depending on the pots and pans used and the amount of food
they contain, and are not indicative of a defect of any kind.
In addition, the induction hob is equipped with an internal cooling system to control the temperature of electronic parts; as a result, during operation and for several
minutes after the hob has been switched off, the noise of the cooling fan will be audible. This is perfectly normal and indeed essential for proper functioning of the
appliance.
CLEANING
WARNING
-Do not use steam cleaners.
-Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H”)
Call the After-Sales Service and specify the error code
NOISES MADE BY THE HOB
EN14
NOTE:
When making quick-cook foods that require perfect heat distribution (e.g. pancakes) on the 28 cm double cooking zone (where present), use pans no greater than
24 cm in diameter. For delicate cooking (for example, melting chocolate or butter) use the smaller diameter single zones.
POWER LEVEL TABLE
Power levelType of cookingLevel use
(indicating cooking experience and habits)
Max. power
BoostFast heating
Ideal for rapidly increasing the temperature of food to fast boiling in the case of water or rapidly
heating cooking liquids
8-9Frying - boiling
Ideal for browning, starting to cook, frying deep frozen products, fast boiling
High power
7-8
Browning - sautéing - boiling -
grilling
Ideal for sautéing, maintaining a lively boil, cooking and grilling (for a short period of time,
5-10 minutes)
6-7
Browning - cooking - stewing -
sautéing - grilling
Ideal for sautéing, maintaining a light boil, cooking and grilling (for a medium period of time,
10-20 minutes), preheating accessories
Medium power
4-5
Cooking - stewing - sautéing -
grilling
Ideal for stewing, maintaining a gentle boil, cooking (for a long period of time). Creaming pasta
3-4
Cooking - simmering -
thickening - creaming
Ideal for long-cooking recipes (rice, sauces, roasts, fish) with liquids (e.g. water, wines, broth, milk),
creaming pasta
2-3
Ideal for long-cooking recipes (less than a litre in volume: rice, sauces, roasts, fish) with liquids
(e.g. water, wines, broth, milk)
Low power
1-2
Melting - defrosting - keeping
food warm - creaming
Ideal for softening butter, gently melting chocolate, thawing small products and keeping just-cooked
food warm (e.g. sauces, soups, minestrone)
1
Ideal for keeping just-cooked food warm, for creaming risottos and for keeping serving dishes warm
(with induction-suitable accessory)
OFF
Zero
power
Support surface
Hob in stand-by or off mode (possible end-of-cooking residual heat, indicated by an “H”)
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Smeg SIM562B at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Smeg SIM562B in the language / languages: English as an attachment in your email.
The manual is 2,48 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.