331785
8
Zoom out
Zoom in
Previous page
1/11
Next page
28 224244
4. Fitting by trained personnel
4.1 Worktop cut-out
Carry out all cutting out of furniture units and worktops before fitting the
appliance, and remove all sawdust and chips.
The dimensions of the worktop recess can be seen in the dimension
drawing (figs. 1+2)
The cut sections should be sealed with a water-repellent protection
paint.
The worktop and the hob must be fitted horizontally. A tilted hob is
under tension and this increases the danger of breaking.
4.2 Installation
Before installing the hob, check that the all-round hob seal has no gaps.
If the induction hob is installed in a worktop with a ceramic or similar cover (tiles), remove the hob seal and seal
the hob from the worktop with a plastic seal, such as heat-resistant silicone rubber.
Attention!
If the hob is installed above furniture parts (side walls, drawers, etc.) it
must be ensured that accidental contact with the underside of the hob is
prevented by means of a touch guard. The touch guard may only be
capable of removal with suitable tools and must be attached to the
underside of the cooking surface at a minimum distance of 20 mm so
that the mains connection cable does not touch the underside of the
cooking surface (fig. 4). The back wall of the cabinet must be open in
order to provide for air circulation. The front transverse strip of the
furniture must be removed so that an opening is provided for air flow
underneath the worktop over the entire width of the unit. The distance
between induction hob and kitchen furniture resp. built-in unit must pro-
vide for sufficient ventilation of the induction. The ventilation openings
must be thermically devided with the attached screen shield. Thus a
back-flow of warmed air is prevented from entering the cool air intake.
Attention! The screen shield must not cover the ventilation openings. If
necessary, shorten the shield up to the furniture or built-in unit. Avoid
excessive thermal development from below e.g. from a baking oven
without a appliance cooling device.
Remove any transverse strips underneath the worktop at least in the area of
the worktop cut-out.
Place the hob carefully into the cut-out and fasten it to the worktop with the fasteners (fig. 3). Tighten the screws
with a hand screw driver only; do not use a battery-operated screw driver.
Make sure that the worktop and the hob are horizontal. In addition, make sure that no liquids can penetrate
between the edge of the hob and the worktop or between the hob and the wall and come into contact with any
electrical appliances. Use sealing sections, strips, agents, etc.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smeg se2842id at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smeg se2842id in the language / languages: English as an attachment in your email.

The manual is 0,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smeg se2842id

Smeg se2842id User Manual - German - 11 pages

Smeg se2842id User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info