327491
19
Zoom out
Zoom in
Previous page
1/36
Next page
EN
Instructions for the User
17
10.2.4 End of a cooking cycle
At the end of the set duration or when you press PT2 to finish the cooking
cycle, you will hear three beeps and the display will show the word “End”
flashing, the oven starts the steam-reduction function.
This function gradually releases the steam from the cavity, so that there is
no sudden rush of steam when the appliance door is opened.
This function takes around 3 minutes and during it the display shows the
word “VAP”. If you want to start a new cooking cycle press PT2 and rotate.
WARNING! WHEN OPENING THE DOOR DURING OR COMPLETION
OF THE COOKING CYCLE WITHOUT STOPPING IT AS DESCRIBED,
BE CAREFUL OF THE FLOW OF HOT AIR AND/OR STEAM COMING
OUT OF THE COOKING CHAMBER. STEP BACK OR TO THE SIDE TO
AVOID BURNS.
The cooling fan can continue to run for a certain length of time after
the appliance has been switched off. This is a normal function that is
meant to reduce the temperature inside the oven.
In the meantime, as soon as the water in the boiler reaches below 75 ºC it
is pumped back to the water tank. This phase can take as long as 10
minutes and the DSP1 shows the message PUMP”. If the display shows
“FULL” it means that the water has to match water inside. Please empty
the tank and place it again.
When the display shows the word “DEP”, this means that the water was
pumped and that the water tank can be removed.
Remove the water tank and dry it thoroughly. Let the cooking space cool
down for a moment and then clean and dry it with a cloth or sponge. The
door should be left open for some time so that the appliance can dry
completely.
10.3 Secondary menu
This appliance also has a concealed "secondary menu" allowing the user
to:
1. Activate or deactivate the Show Room function (which disables all the
heating elements so that only the control panel works);
2. Perform a Descale cycle;
3. Change the Water Hardness Level
4. Activate or deactivate the child safety device ( );
10.3.1 Show Room Function
With the oven in OFF status (see point “8.2 Operating settings”) keep PT1
pressed until the message OFF SHO appears on DSP1 and DSP2. This
means that the SHOW ROOM function (which disables all the heating
elements so that only the control panel works) is not active.
Turn PT1 to the right or left to activate (ON SHO) or deactivate (OFF SHO)
this function. To use the oven normally, set OFF SHO.
After setting the parameter required, press PT2 to return the oven to the
initial standby status.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smeg s45va at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smeg s45va in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smeg s45va

Smeg s45va User Manual - German - 39 pages

Smeg s45va User Manual - Dutch - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info