125995
10
Zoom out
Zoom in
Previous page
1/27
Next page
User instructions
32
In case that the door is opened during the operation, to the next door closing it is going to be
necessary to start the program as shown in paragraph
S
TART PROGRAM
”. The program will resume
from the point in which it was interrupted.
In case that the tub temperature is higher than 50°C the program will start about 30 seconds
later.
3.2 Washing programs
The dishwasher is equipped with a control panel, described in chapter "3. Description of the
controls", from which it is possible to carry out all the power switch-on, switch-off and programming
operations.
Before starting a washing program make sure that:
The water supply tap is
open.
The
correct amount of detergent
has been added to the
dispenser
.
The baskets have been
correctly loaded.
The spray arms are able to
rotate freely
and without obstruction.
The dishwasher door is
securely closed
.
HALF LOAD WASH FUNCTION
(on some models only)
Pressing button
½ LOAD WASH (4)
selects washing on the top basket only.
After selecting the program, proceed as follows:
press the button
½ LOAD WASH (4)
once to select the top basket (the relative light comes on);
press the button
½ LOAD WASH (4)
again to return to full load wash status (the light goes
out).
The
½ LOAD
wash option can be selected in all programs
except the soak
program.
N.B.:
selecting the
½ LOAD
option changes the duration of the program.
It is possible to place a cutlery basket inside the basket selected for the
HALF-LOAD
program; the
other basket
must remain empty.
WARNING: do not load dishes and cutlery into the non-selected basket, because the water
spray will only reach the selected basket.
DELAY PROGRAM
(on some models only)
Pressing b utton
DELAY PROGRAM
(3)
in sequence delays the start of the program by
3
,
6
or
9
hours
. This allows you to set the dishwasher to work at specific times of day.
After selecting the delay, start the program in the normal way (see relative section).
The appliance will prewash the dishes, after which the “delay program set previously will come into
effect (the phase lights switch off and the light relating to the delay set flashes).
To
reset or change the delay
once the program has started:
press the
START/PAUSE
button
(5)
for a few seconds, until the
PROGRAM PHASES
lights
(10)
come on;
press the
DELAY PROGRAM
button
(3)
several times
“until the program delay” returns to zero
(all the lights indicating the delay go out);
press the
START/PAUSE
button
(5)
to start the new program.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smeg pla 651 b at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smeg pla 651 b in the language / languages: English as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smeg pla 651 b

Smeg pla 651 b User Manual - German - 27 pages

Smeg pla 651 b User Manual - Dutch - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info