Manual Smeg LST147 (page 8 of 30) (English)

459688

Zoom out

Zoom in

1/30

2.3 CONNECTING TO THE WATER SUPPLY

1. Check that the water supply pressure is in the following range: 0,05-0,9MPa. With

higher pressures, use a pressure reducer.

2. Connect the cold water supply hose (blue screw collar) to the cold water tap with ¾

gas threaded connector, taking care to tighten firmly to prevent leaks. The water sup-

ply hose must not be kinked or crushed and must not be changed or cut. Threaded

connections must only be tightened by hand.

3. When appliances are supplied with hot water, the intake water temperature must not

exceed 60°C and the hose with red screw collar must be connected to the hot water supply tap.

Warning!

• If the connection is made to new pipelines, or lines which have been out of use for a long time, allow a con-

siderable amount of water to flow out before connecting the intake hose. This prevents any sand or other dirt

from fouling the filters installed in the appliance to protect the water intake valves.

• The new intake hose supplied with the appliance must be used, and the old water supply hose must not be

used.

2.4 CONNECTING TO THE DRAIN

1. Insert the end of the drain hose into a drain pipe having inside diameter of at least 4 cm, at least 50 to 90 cm

above floor level, or connect it securely (using the plastic fitting on the elbow in the hose) to a sink or bathtub.

2. In all cases, check that the end of the drain hose is securely fixed to prevent the repulsive force of the water

from pushing it out of place.

Warning!

• Avoid kinks or restrictions to ensure effective drainage.

• Any drain hose extensions must be no more than 1 metre long, must be of the same diameter and must be

free from restrictions of all kinds.

• The end of the drain hose must never be submerged in water.

2.5 ELECTRICAL CONNECTION

Before connecting the plug to the power socket ensure that:

1. The electrical system voltage is the same as that stated on the nameplate on the front of the appliance,

in the zone visible when the door is open. The rated power supply and the fuses required are specified

on the nameplate.

2. The meter, safety breakers, power supply line and power socket are rated to withstand the maximum lo-

ad required, stated on the nameplate.

3. The power supply socket and the plug fitted to the appliance are compatible without the use of reduc-

tions, multiple sockets, adapters and extension leads which might cause overheating or scorching.

If the power supply socket is not compatible with the plug supplied, replace the socket with one of the

appropriate type.

Warning

• The power plug must be accessible after the appliance has been installed.

• It is absolutely essential to connect the appliance to earth. Connect the plug to a socket with an earth

connection in good working order.

The manufacturer declines all liability for direct or indirect injury or damage deriving from a non-existent

or defective earth connection. Correct electrical connection guarantees conditions of maximum safety.

• This appliance is compliant with the requirements of EEC directive 89/336 of 3.5.89 (including the amend-

ment directive 92/31/EEC) concerning the elimination of radio-frequency disturbance.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Smeg LST147 in the language / languages: English as an attachment in your email.

The manual is 4,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Smeg LST147

Smeg LST147 User Manual - German - 30 pages

Smeg LST147 User Manual - Dutch - 30 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Smeg LST147 Manual

Product: