109389

Smeg KSEV-910 X1 Manual

22
Zoom out
Zoom in
Previous page
1/107
Next page
22
Functioning - 6-key electronic model
12 34 5F6
1- Motor OFF key.
2- Diminishes the speed.
3- Increases the speed.
4- 5/15 minutes timer. Inserts and extracts the timer.
The speed in function is turned off automatically.
5- Resets carbon filters saturation indicator.
When the F led lights up, the carbon filter should be
cleaned or changed.
Press for at least 3 seconds after having changed the
carbon filter. The F led will turn off to indicate the resetting
of the saturation indicator.
Note: This led switches ON even if the carbon filter has
not been mounted.
6- ON/OFF light.
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Electronic model with sensor
12 3S
FC
Sensor
Reset
0/I
T1 T2 T3 T4 T51234
T1. Hood On/Off key
T2. Increase cyclical motor speed key.
Pressing the first time activates speed 1. A Led (1-2-3),
corresponding to each speed, switches on. Led 4 flashes
at intensive speed.
After 5 minutes intensive speed is reduced to the second
speed. If key T2 is pressed before the end of the 5
minutes, the hood retunes to the first speed.
T5. Lights On/Off key.
Filter signals
(function active with the hood on): the fats filter signal
appears after 80 hours functioning (Led 1 flashing).
The carbon filter signal appears after 320 hours (Led 2
flashing). In the case of simultaneous signalling of the fats
and carbon filters, Leds 1 and 2 flash alternatively.
Reset filter signals:
press key T4 for 3 seconds until Led 1 switches off (fats
filter). In the case of both filters (fats and carbon)
signalling, repeat the operation just described: pressing T4
the first time switches off Leds 1 and 2 that are flashing
alternatively. Immediately afterwards Led 2 flashes again:
at this point press T4 again for 3 seconds. A beep signals
each time the operation is completed.
Enabling the carbon filter signal:
the hood is enabled only for the fats filter signal. To enable
the carbon filter signal: hood in Off, press keys T2 and T4
for 3 seconds. The flashing of Leds 1 and 2 signals the
completion of the setting. To disenable the carbon filter
signal, repeat this operation again (always with the hood
in Off). A beep signals each time the operation is
completed.
Automatic calibration:
the system carries calibration out automatically about
every 30 minutes (calibration of the parameters
functioning of the sensors).
Manual calibration:
with the hood in Off, press keys T3 and T4 until the beep.
Automatic functioning:
to activate automatic functioning, press key T3: Led 4
switches on. To return to manual functioning, press key
T1, T2 or T3.
Sensors test:
this happens continuously during automatic functioning. In
the case of damage all the Leds flash: in this case, return
to manual functioning, pressing keys T1, T2 or T3.
Selecting cooking top:
this operation optimises the automatic functioning of the
hood: with the hood in Off press keys T2 and T3 for about
3 seconds until the cooking top at present in use is seen:
gas top - Led 1 on
induction top - Led 2 on
electric top - Led 3 on.
Select the cooking top requested pressing T2, then press
T2 and T3 simultaneously for three seconds until the
Beep. Alt the end the hood switches off.
The gas top is the default state.
Attention: carry out this operation the first time the hood
is switched on.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Smeg KSEV-910 X1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Smeg KSEV-910 X1 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info