Manual Smeg ksei61s (page 11 of 52) (English, German, Dutch, French, Italian)

133031

Zoom out

Zoom in

1/52

Installing the aesthetic panel (*)

a. Extract the steam collector (freeing it from the blocking

hooks - Fig. 5).

b. Put perforation diagram N3 on the REAR of aesthetic

panel J (the arrow on the diagram turned upward towards

the UPPER EDGE of the aesthetic panel). Fig. 6

c. Make BLIND HOLES K as indicated. Fig. 6

d. Put the steam collector over the aesthetic panel and fix it

with 8 screws L. Fig. 6

e. Remount the door on the hood, first on upper guides M1,

then on the lower M2. Fig. 6

f. Close completely and re-open the door to check its

correct sliding on the guides.

Electrical or mechanical valve (*)

Fig. 11

In some products an electrically or mechanically activated

valve is envisaged instead of an aspiration motor.

This is usually installed on discharge outlet B1 and fixed to the

caisson of the hood with 3 screws, while a stopper is installed

in outlet B2, fixed in its turn with 1 screw.

If you want to install the valve on outlet B2, dismantle the

valve from the caisson, remove the fixing screws, and install it

in place of the stopper, the latter to be fixed on the cover of

outlet B1.

Installation

a. Use perforation diagram N2 (*). Position the diagram on

the front edges of the wall unit (right wall unit, B side) –

(left wall unit, C side) WITHOUT CONSIDERING THE

THICKNESS OF THE DOORS, and make the holes as

indicated. Fig. 8

b. If necessary, fix the hood to the wall

, putting template N1

(*) on the wall so its upper edge coincides with the upper

edge of template N2 (*). Fig. 7-8

c. Make the holes as indicated. Fix 2 hooks (*) R to the wall

with screws and dowels. Fig. 7

d. In case the thickness of the lateral wall units is 16mm,

put, with embedded fixing, the O (*) spacers at the sides

of the hood in correspondence with the holes used for the

passage of the fixing screws to the lateral wall units. Fig.

e. Hang the hood onto the hooks (*) and adjust the position

of the hood with headless screws S1 and adjusting the

position of the hooking brackets with screws S2. Fig. 7

f. Fix the hood to the lateral wall units with 4 screws P. Fig.

g. Mount the lower corner Q (*) to the hood with two screws

and plastic washers T. They will serve to cover possible

spaces between the rear of the hood and the wall. Fig. 7

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Use the keys or buttons envisaged for the control of the lights

and the power of the available suction.

Only in some models: switching on and off the fan that

adjusts the suction power and, in some cases, switching the

lights on and off, is controlled by opening and closing the

steam collector.

If your product is provided with an electrically or mechanically

activated valve, the keys and/or the buttons and/or the

handles available are for controlling the lights and for opening

and closing the valve.

Maintenance

Before performing any maintenance operation, isolate the

hood from the electrical supply by switching off at the

connector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the

same frequency with which you carry out maintenance of the

fat filters) internally and externally. Clean using the cloth

dampened with neutral liquid detergent. Do not use abrasive

products.

DO NOT USE ALCOHOL!

Grease filter

Traps cooking grease particles.

If situated inside the support grill, it may be one of the

following types:

Paper filter must be replaced once a month or if colouring

appears on upper side, in such cases the colouring is evident

through the grill openings.

Sponge filter should be washed with hot soapy water once a

month and replaced every 5 to 6 washes.

Metallic filter must be cleaned once a month, with non

abrasive detergents, by hand or in dishwasher on low

temperature and short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

To access fats filter V, open the suction grill with hooks H1 or

H2 (depending on the model in possession) and free it from

the W stops. Fig. 9

Some models are provided with anti-grease filter incorporated

in the suction grill, these should be removed from the housing

by pulling the handles H2 (Fig. 9) upwards and sliding out,

wash these filters as with metallic filters.

Charcoal filter (filter version only)

It absorbs unpleasant odours caused by cooking.

The saturation of the activated charcoal occurs after more or

less prolonged use, depending on the type of cooking and the

regularity of cleaning of the grease filter.

In any case it is necessary to replace the cartridge at least

every four mounths (or when the filter saturation indication

system – if envisaged on the model in possession – indicates

this necessity).

Cover the grill that protects the suction motor with the carbon

filter so that the slots on the filter correspond to the pins on the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Smeg ksei61s in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Smeg ksei61s Manual

Product: