677295

Skytech 1001 - A remote control system Manual

3
Zoom out
Zoom in
Previous page
1/6
Next page
ELECTRONIC SPARK SYSTEM CHECK
Slide the 3-position button on the remote receiver to the • ON position. The spark electrode should begin sparking to ignite the pilot.
Afterthepilotameislit,themaingasvalveshouldopenandthemaingasameshouldignite.
Slide the button to • OFF.Themaingasameandpilotameshouldbothextinguish.
Slide the button to • REMOTE,thenpresstheON button on the transmitter to change the system to on. The spark electrode should
beginsparkingtoignitethepilot.Afterthepilotislit,themaingasvalveshouldopenandthemaingasameshouldignite.
LEARNING TRANSMITTER TO RECEIVER
•
Each transmitter uses a unique security code. It will be necessary to press the LEARN button on the receiver to accept the trans-•
mittersecuritycodeuponinitialuse,ifbatteriesarereplaced,orifareplacementtransmitterispurchasedfromyourdealerorthe
factory.Inorderforthereceivertoacceptthetransmittersecuritycode,besuretheslidebuttononthereceiverisintheREMOTE
position;thereceiverwillnotLEARNiftheslideswitchisintheONorOFFposition.TheLEARNbuttoninlocatedonthefrontface
of the receiver; inside the small hole labeled LEARN. Using a small screwdriver or end of a paperclip gently press and release
the black LEARN button inside the hole. When you release the LEARN button the receiver will emit an audible “beep”. After the
receiver emits the beep press ANY transmitter button and release. The receiver will emit several beeps indicating that the transmit-
ter’s code has been accepted into the receiver.
REV 4/15/11 Page 3
WIRING ELECTRONIC SPARK IGNITIONS
ELECTRONIC MODULE
TR
TH
REMOTE
RECEIVER
neutral wire
24VAC
hot wire
120VAC
110/24VAC
Transformer
Theremotecontrolreceivercanbeconnected,inseries,toa24VAC
transformertotheTR(transformer)terminalontheELECTRONIC
MODULE.Connectthehotwirefromthe24VACtransformertoeither
ofthewireterminalsontheremotereceiver.Connectanotherwirebe-
tween the other receiver wire terminal and the TH (thermostat) terminal
ontheELECTRONICMODULE.
WIRING INSTRUCTIONS
Aqualiedelectricianshouldinstalltheremotecontrolsystem.
TERMINAL BLOCK
ON MILLIVOLT
GAS VALVES
TH
TP
TP
TH
THERMOPILE/
PILOT LIGHT
REMOTE
RECEIVER
ConnectonewirefromtheremotereceivertotheTHterminalonthegas•
valve.
ConnecttheotherwirefromtheremotereceivertotheTH/TPterminalon•
the gas valve.
WIRING MILLIVOLT VALVES
MILLIVOLT SYSTEM CHECK
Ensurethatthepilotameislit.•
Slide the 3-position button on the remote receiver to the • ONposition.Themaingasame(i.e.,there)
should ignite.
Slide the button to • OFF.Themainameshouldextinguish(thepilotamewillremainon).
Slide the button to • REMOTE,thenpresstheON button on the transmitter to change the system to on. The main
gasameshouldignite.
Skytech 1001-A
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skytech 1001 - A remote control system at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skytech 1001 - A remote control system in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info