506114
4
Zoom out
Zoom in
Previous page
1/18
Next page
4 - 18
INPUT PANEL
8” & 10” Versie:
1. Input connector for microphone
2. Volume control for the microphone
3. Volume control for the line input
4. Line input connector for the audio input source e.g. mixer, CD
player, etc.
5. Output connector to a second box or amplifier (line level)
6. Tone control for the output
12” & 15” Versie:
1. Input connector for microphones
2. Volume control for the microphone
3. Volume control for the line input
4. Volume control for the output
5. Tone control for the output
6. Output connector to a second box or amplifier (line level)
7. Line input connector for the audio input source e.g. mixer, CD
player, etc.
TROUBLESHOOTING
One certain method of determining if a speaker is faulty is to substitute a speaker that is known to work
correctly for the suspected problem speaker. If the “normally correct speaker” is experiencing the same
difficulties or problems as the suspected problem speaker, use the information below to isolate the problem.
Possible cause Action
No output
Cables Reseat all connectors
Substitute known good cables
Check solder joins
Inspect cable for damage
Inspect wire or connector for stray strand that may short
Intermittent
Poor connections While it is possible for a faulty speaker to exhibit intermittent output, it’s more likely
that an output cable/connector is the problem. Check the soldering on your
connectors.
Constant noise, buzzing and/or humming
Faulty electronic Any constant noise originates in the amplifier, mixer, signal processing, source
device in the signal devices, or line-level wiring. Check and correct system grounding as required. chain
check for noisy sources or electronic components. Check wiring for shielding.
Poor low-frequency output
Improper polarity When two speakers in close proximity to each other are connected out-of-polarity,
they can partially cancel each other out, especially at low frequencies. Check your
speaker cables to be sure they are all identically wired and connected. Check the
balanced line signal cables to be sure they are all correctly wired.
Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the unit. This
would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use
or disrespect of the warnings contained in this manual. Tronios cannot be held responsible for personal injuries caused by a
disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skytec SP Hi-End Passive Speaker 170.306 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skytec SP Hi-End Passive Speaker 170.306 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info