617592
174
Zoom out
Zoom in
Previous page
1/204
Next page
Preparations for using the breakdown kit
Read and observe on page 170 first.
The following preparatory work must be carried out before using the puncture
repair kit.
Have all the occupants get out. The passengers should not stand on the
road (instead they should remain behind a crash barrier, for instance) while
the wheel is being changed.
Switch off the engine.
Engage the 1st gear or place the selector lever of the automatic transmission
in the P-position.
Apply the handbrake firmly.
Check that you can carry out the repairs with the breakdown kit » page 169.
Uncouple a trailer.
Remove the
breakdown kit from the boot.
Stick the appropriate sticker
2
» Fig. 152 on page 170 onto the dashboard in
the driver's field of view.
Unscrew the valve cap.
Use the valve remover
1
to unscrew the valve core and place it on a clean
surface (rag, paper, etc.).
Sealing and inflating the tyre
Read and observe
on page 170 first.
Sealing
Shake the tyre inflator bottle
10
» Fig. 152 on page 170 vigorously several
times.
Firmly screw the inflation hose
3
onto the tyre inflator bottle
10
in a clock-
wise direction. The film on the cap is pierced automatically.
Remove the plug from the inflation hose
3
and plug the open end fully onto
the tyre valve.
Hold the bottle
10
with the bottom facing upwards and fill all of the sealing
agent from the tyre inflator bottle into the tyre.
Remove the empty tyre inflator bottle from the valve.
Screw the valve core back into the tyre valve using the valve remover
1
.
Inflating
Screw the air compressor tyre inflation hose
5
» Fig. 152 on page 170 firmly
onto the tyre valve.
Check that the air release valve
7
is closed.
Start the engine and run it in idle.
Plug the connector
9
into 12 Volt socket » page 82, 12-volt power outlet.
Switch on the air compressor with the ON and OFF switch
8
.
Allow the air compressor to run until a pressure of 2.0 - 2.5 bar is achieved.
Maximum run time of 8 minutes » .
Switch off the air compressor.
If you cannot reach an air pressure of 2.0 – 2.5 bar, unscrew the tyre inflation
hose
5
from the tyre valve.
Drive the vehicle 10 metres forwards or backwards to allow the sealing agent
to “distribute” in the tyre.
Firmly screw the tyre inflation hose
5
back onto the tyre valve and repeat
the inflation process.
If you cannot reach the required tyre inflation pressure here either, this
means the tyre has sustained too much damage. You cannot seal with tyre
with the breakdown kit » .
Switch off the air compressor.
Remove the tyre inflation hose
5
from the tyre valve.
Once a tyre pressure of 2.0 – 2.5 bar is reached, the journey may be continued
at a maximum speed of 80 km/h (50 mph).
WARNING
If you cannot inflate the tyre to at least 2.0 bar, this means the damage
sustained was too serious. The sealing agent cannot be used to seal the
tyre.
Do not drive the vehicle any further! Seek help from a specialist ga-
rage.
The tyre inflation hose and air compressor may get hot as the tyre is be-
ing inflated – there is a risk of burning.
CAUTION
Switch off the air compressor after running 8 minutes at the latest – there is a
risk of overheating. Allow the air compressor to cool a few minutes before
switching it on again.
Notes for driving with tyre repaired
Read and observe on page 170 first.
The inflation pressure of the repaired tyre must be checked after driving for 10
minutes.
171
Emergency equipment and self-help
174


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skoda Roomster - 2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skoda Roomster - 2015 in the language / languages: English as an attachment in your email.

The manual is 14,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Skoda Roomster - 2015

Skoda Roomster - 2015 User Manual - German - 212 pages

Skoda Roomster - 2015 User Manual - Dutch - 212 pages

Skoda Roomster - 2015 User Manual - French - 212 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info