Manual Skil 9390 (page 7 of 176) (All languages)

591208

Zoom out

Zoom in

1/176

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or binding of the

wheel in the cut and the possibility of kickback or wheel

breakage.

b) Do not position your body in line with and behind

the rotating wheel. When the wheel, at the point of

operation, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

c) When the wheel is binding or when interrupting a



hold the power tool motionless until the wheel

comes to a complete stop. Never attempt to remove



motion, otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of

wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

The wheel may bind,

walk up or kickback if the power tool is restarted in the

workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

5) SAFETY WARNINGS SPECIFIC FOR SANDING

OPERATIONS

a) When sanding, do not use excessively oversized

sanding disc paper. Follow the manufacturers’

recommendations when selecting sanding paper.

Larger sanding paper extending beyond the sanding

pad presents a laceration hazard and may cause

snagging, tearing of the disc, or kickback.

6) SAFETY WARNINGS SPECIFIC FOR WIRE

BRUSHING OPERATIONS

a) Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress

the wires by applying excessive load to the brush.

The wire bristles can easily penetrate light clothing and/

or skin.

b) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel or

brush may expand in diameter due to work load and

centrifugal forces.

GENERAL

 This tool is not suitable for wet grinding/cutting

 Only use the anges which are supplied with this tool

 This tool should not be used by people under the age

of 16 years

 Always disconnect plug from power source before

making any adjustment or changing any accessory

wheel may either jump toward or away from the operator,

depending on the direction of the wheel’s movement at

the point of pinching. Abrasive wheels may also break

under these conditions.

 Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) 

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

b) Never place your hand near the rotating accessory.

The accessory may kickback over your hand.

c) Do not position your body in the area where power

tool will move if kickback occurs. Kickback will

propel the tool in the direction opposite to the wheel’s

movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create frequent

kickback and loss of control.

3) SAFETY WARNINGS SPECIFIC FOR GRINDING AND



a) Use only wheel types that are recommended for



for the selected wheel. Wheels for which the power

tool was not designed cannot be adequately guarded

and are unsafe.

b) The grinding surface of the centre depressed

wheels must be mounted below the plane of the

guard lip. An improperly mounted wheel that projects

through the plane of the guard lip cannot be adequately

protected.

c) The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator. The guard helps to protect the operator from

broken wheel fragments, accidental contact with wheel

and sparks that could ignite clothing.

d) Wheels must be used only for recommended

applications. For example: Do not grind with the side of

a cut-o wheel. Abrasive cut-o wheels are intended for

peripheral grinding; side forces applied to these wheels

may cause them to shatter.

e) 

correct size and shape for your selected wheel.

Proper wheel anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-o

wheels may be dierent from grinding wheel anges.

f) Do not use worn down wheels from larger power

tools. A wheel intended for a larger power tool is not

suitable for the higher speed of a smaller tool and may

burst.

4) ADDITIONAL SAFETY WARNINGS SPECIFIC FOR

CUTTING OFF OPERATIONS

a) 

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 9390 in the language / languages: All languages as an attachment in your email.

The manual is 4,12 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 9390 Manual

Product: