701695
7
Zoom out
Zoom in
Previous page
1/88
Next page
7
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or
remove the battery pack, if detachable, from the
power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
ADDITIONAL SAFETY WARNINGS
PERSONAL SAFETY
Never blow debris in the direction of bystanders
Do not blow and vacuum materials that are
hazardous to one’s health (such as dust from beech or
oak wood, masonry dust, asbestos)
The noise level when working can exceed 85 dB(A); wear
ear protection
Wear a dust mask when working in a dusty environment
Always disconnect plug from power source during work
breaks or before cleaning, maintenance, making
adjustments and changing accessories, in order to
reduce the risk of starting the tool accidentally
ELECTRICAL SAFETY
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
Do not blow and vacuum liquids (the penetration of
liquids increases the risk of an electric shock)
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
Always switch o tool and disconnect plug from power
source if the power supply cord or the extension cord is
cut, damaged or entangled (do not touch the cord
before disconnecting the plug)
Never use the tool when cord is damaged; have it
replaced by a qualied person
BEFORE USE
Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a
qualied person; never open the tool yourself
When vacuuming, never use the tool without the dustbag
in place
Regularly check the dustbag for wear or damage
DURING USE
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
Always ensure that the ventilation openings are kept clear
of debris
In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Wear protective glasses
5 Double insulation (no earth wire required)
6 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
On/o
- switch on the tool by pulling trigger A
- lock the switch for continuous use by pressing button
B
- unlock the switch by pulling again trigger A and then
releasing it
- switch o the tool by releasing trigger A
! before switching on the tool, ensure that it is not
in contact with any object
! after switching off the tool the motor continues to
run for a few seconds
• Blowing 7
- insert tabs inside nozzle C into slots of air outlet D and
lock nozzle into place by turning it clockwise
! when blowing always ensure that air inlet E 2 is
kept clear of debris/impurities
• Vacuuming 8
- insert tabs inside nozzle C into slots of air inlet E and
lock nozzle into place by turning it clockwise
- do not vacuum sharp-edged or hot materials (such as
glass splinters, hot ash or metal chips)
! when vacuuming always mount dustbag F onto
air outlet D
- regularly empty dustbag F (the vacuum capacity
decreases considerably when the dustbag is full)
Airow control (7 positions)
- turn wheel G upwards for increasing the air volume
- turn wheel G downwards for reducing the air volume
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 8600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 8600 in the language / languages: All languages as an attachment in your email.

The manual is 5,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info