Manual Skil 8200AA (page 7 of 92) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

482530

Zoom out

Zoom in

1/92

Power tools are dangerous in the hands of untrained

users.

e) Maintainpowertools.Checkformisalignmentor

bindingofmovingparts,breakageofpartsandany

otherconditionthatmayaffectthepowertool’s

operation.Ifdamaged,havethepowertoolrepaired

beforeuse. Many accidents are caused by poorly

maintained power tools.

f) Keepcuttingtoolssharpandclean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Usethepowertool,accessoriesandtoolbitsetc.,in

accordancewiththeseinstructions,takinginto

accounttheworkingconditionsandtheworktobe

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5)SERVICE

a) Haveyourpowertoolservicedbyaqualifiedrepair

personusingonlyidenticalreplacementparts. This

will ensure that the safety of the power tool is maintained.

SAFETYINSTRUCTIONSFORTACKERS

• Alwaysassumethatthetoolcontainsfasteners

(careless handling of the tacker can result in unexpected

ring of fasteners and personal injury)

• Donotpointthetooltowardsyourselforanyone

nearby (unexpected triggering will discharge the fastener

causing an injury)

• Donotactuatethetoolunlessthetoolisplaced

firmlyagainsttheworkpiece (if the tool is not in

contact with the workpiece, the fastener may be deected

away from your target)

• Disconnectthetoolfromthepowersourcewhenthe

fastenerjamsinthetool (while removing a jammed

fastener, the tacker may be accidentally activated if it is

plugged in)

• Usecautionwhileremovingajammedfastener (the

mechanism may be under compression and the fastener

may be forcefully discharged while attempting to free a

jammed condition)

• Donotusethistackerforfasteningelectricalcables

(it is not designed for electric cable installation and may

damage the insulation of electric cables thereby causing

electric shock or re hazards)

• Securetheworkpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction

concerning use of the tool by a person responsible for

their safety

• Ensure that children do not play with the tool

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

EXPLANATIONOFSYMBOLSONTOOL

3 Read the instruction manual before use

4 Double insulation (no earth wire required)

5 Do not dispose of the tool together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Loading staples/nails 6

! disconnecttheplug

- turn tool upside down

- press lever A while pulling slider B backwards

- insert the staple/nail strip into magazine C with legs

facing upward (maximal capacity 100 staples/80 nails)

- push slider B against tacker head D until it snap-locks

- when inserting a nail strip (not supplied with the tool)

tilt the tool in such a way, that the nail strip rests

against the magazine side which corresponds with the

nail symbol on tacker head D 7

- reload magazine C when end of staple- or nail strip

shows in opening H 2

• Operating the tool 8

- switch on the tool by pushing switch E in “I” position

- rmly press tacker head D against the workpiece until

it is pushed in completely

- briey press switch F and then release again

! whileworking,alwaysholdthetoolatthe

grey-colouredgriparea(s)

- switch o the tool by pushing switch E in “O” position

• Impact control 9

With wheel G the required impact level can be adjusted

steplessly from minimum to maximum (- / +)

- “-” for thin and light materials such as foils and fabrics

- “+” for thick and tough materials such as hard woods

and walls

- before starting a job, nd the optimal impact level by

testing out on spare material

APPLICATIONADVICE

• Fastening panels 0

• Fixing textiles !

• For stapling hard wood use shorter staples than the ones

supplied with the tool

• Avoid blank shots in order to reduce the wear of the

impact strike

• For more tips see skileurope.com

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 8200AA in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 8200AA Manual

Product: