Manual Skil 8100 (page 8 of 160) (All languages)

591190

Zoom out

Zoom in

1/160

 For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

 Only use the anges which are supplied with this tool

 Never use accessories with a "blind" threaded hole

smaller than M14 x 22 mm

 Never use grinding/cutting discs with this tool

OUTDOOR USE

 Connect the tool via a fault current (FI) circuit breaker

with a triggering current of 30 mA maximum

BEFORE USE

 Before using the tool for the rst time, it is recommended

to receive practical information

 Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

 Do not work materials containing asbestos

(asbestos is considered carcinogenic)

 Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

 Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

 Follow the dust-related national requirements for the

materials you want to work with

 Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

 Do not clamp the tool in a vice

 Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

 Keep hands away from rotating accessories

 Do not continue to use worn, torn or heavily clogged

sanding sheets

 When sanding metal, sparks are generated; do not

use vacuum cleaner and keep other persons and

combustible material from work area

 If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

 Never use the tool when cord is damaged; have it

replaced by a qualied person

 In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

 In case of current interruption or when the plug is

accidentally pulled out, immediately switch o the tool in

order to prevent uncontrolled restarting

AFTER USE

 After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

EXPLANATION OF SYMBOLS ON TOOL

Read the instruction manual before use

Double insulation (no earth wire required)

Wear protective glasses and hearing protection

Do not dispose of the tool together with household waste

material

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the operator,

depending on the direction of the wheel’s movement at

the point of pinching. Abrasive wheels may also break

under these conditions.

 Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) 

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

b) Never place your hand near the rotating accessory.

The accessory may kickback over your hand.

c) Do not position your body in the area where power

tool will move if kickback occurs. Kickback will

propel the tool in the direction opposite to the wheel’s

movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create frequent

kickback and loss of control.

3) SAFETY WARNINGS SPECIFIC FOR SANDING

OPERATIONS

a) When sanding, do not use excessively oversized

sanding disc paper. Follow the manufacturers’

recommendations when selecting sanding paper.

Larger sanding paper extending beyond the sanding

pad presents a laceration hazard and may cause

snagging, tearing of the disc, or kickback.

4) SAFETY WARNINGS SPECIFIC FOR POLISHING

a) Do not allow any loose portion of the polishing

bonnet or its attachment strings to spin freely. Tuck

away or trim any loose attachment strings. Loose

and spinning attachment strings can entangle your

ngers or snag on the workpiece.

ADDITIONAL SAFETY WARNINGS

GENERAL

 This tool should not be used by people under the age

of 16 years

 This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the tool by a person responsible for

their safety

 Ensure that children do not play with the tool

 This tool is not suitable for wet sanding

 Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

 SKIL can assure awless functioning of the tool only

when original accessories are used

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Skil 8100 in the language / languages: All languages as an attachment in your email.

The manual is 3,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Skil 8100 Manual

Product: