644680
7
Zoom out
Zoom in
Previous page
1/152
Next page
7
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dierent
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR HEAT GUNS
BEFORE USE:
Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a
qualied person; never open the tool yourself
Inspect tool cord and plug before each use and, if
damaged, have them replaced by a qualied person
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
Inspect the extension cord periodically and replace it, if
damaged
Use the tool and its accessories in accordance with this
instruction manual and in the manner intended for the
tool; use of the tool for operations, dierent from those
normally expected to be performed by the tool, could
result in a hazardous situation
This tool should not be used by people under the age of
16 years
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the tool by a person responsible for
their safety
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
Be sure tool is switched o when plugging in
DURING USE:
• Handlethetoolwithcare;preventfireandburns
- do not touch the air outlet/nozzle and the heated
object; they become extremely hot
- do not hold the air outlet/nozzle too close to the object
to be worked on
- do not direct the hot air ow towards the same surface
for too long
- never look down the air outlet/nozzle
- wear protective gloves and use safety glasses
- never direct the hot air ow towards persons or
animals
- never use the tool for drying hair
- do not leave the tool unattended
- never use the tool in the proximity of inammable
gases or combustible materials (risk of explosion)
- when working with plastic, paint, varnish and similar
materials, inammable and poisonous gases may be
produced; inform yourself beforehand about the
materials to be worked on
- take into account, that heat may be transferred to
combustible materials out of eyesight
- to be on the safe side, have a bucket of water or a re
extinguisher handy, in case any material catches re
• Preventelectricalshock
- never poke anything down the air outlet/nozzle
- avoid body contact with earthed surfaces (e.g. pipes,
radiators, ranges, refrigerators)
- ensure the tool does not get wet
- do not use the tool in damp locations
- when used outdoors, connect the tool via a fault
current (FI) circuit breaker with a triggering current of
30 mA maximum, and only use an extension cord
which is intended for outdoor use and equipped with a
splashproof coupling-socket
• Handlethecordwithcare
- always keep away the cord from the hot air ow and
the air outlet/nozzle
- keep the cord away from heat, oil and sharp edges
- do not carry the tool by the cord, and do not yank the
cord to disconnect it from the socket
- do not suspend the tool by the cord
Never use the tool in conjunction with chemical solvents
Make sure work area is adequately ventilated
Keep work area clean and well lit
Keep children away from work area
Ensure that children do not play with the tool
Inrush currents cause short-time voltage drops; under
unfavourable power supply conditions, other equipment
may be aected (if the system impedance of the power
supply is lower than 0,127 + j0,079 Ohm, disturbances
are unlikely to occur); if you need further clarication, you
may contact your local power supply authority
Stay alert; watch what you are doing, use common sense
and do not operate the tool when you are tired
Take a secure stance; do not overreach, especially on
ladders and stages
Ensure that the tool is switched o, before putting it aside
In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
AFTER USE:
Switch o the tool and disconnect the plug
• Allowthetooltocooldownforatleast30minutes
before storage
Suspend the tool on hanging ring M 2 or set it down on
its rear in an upright position; when doing so, make sure
no combustible materials or inammable gases are in the
proximity
Do not store/leave the tool outdoors
Store the tool in a dry and locked-up place, out of reach
of children
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 8007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 8007 in the language / languages: All languages as an attachment in your email.

The manual is 7,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info