482552
7
Zoom out
Zoom in
Previous page
1/196
Next page
7
capabilities, or lack of experience and
knowledge, unless they have been
given supervision or instruction
concerning use of the tool by a person
responsible for their safety
Always check that the supply voltage
is the same as the voltage indicated
on the nameplate of the tool
Be sure tool is switched o when
plugging in

 

- do not touch the air outlet/nozzle
and the heated object; they
become extremely hot
- do not hold the air outlet/nozzle too
close to the object to be worked on
- do not direct the hot air ow
towards the same surface for too
long
- never look down the air outlet/
nozzle
- wear protective gloves and use
safety glasses
- never direct the hot air ow towards
persons or animals
- never use the tool for drying hair
- do not leave the tool unattended
- never use the tool in the proximity
of inammable gases or
combustible materials (
)
- when working with plastic, paint,
varnish and similar materials,
inammable and poisonous gases
may be produced; inform yourself
beforehand about the materials to
be worked on
- take into account, that heat may be
transferred to combustible
materials out of eyesight
- to be on the safe side, have a
bucket of water or a re
extinguisher handy, in case any
material catches re
 
- never poke anything down the air
outlet/nozzle
- avoid body contact with earthed
surfaces (e.g. pipes, radiators,
ranges, refrigerators)
- ensure the tool does not get wet
- do not use the tool in damp
locations
- when used outdoors, connect the
tool via a fault current (FI) circuit
breaker with a triggering current of
30 mA maximum, and only use an
extension cord which is intended
for outdoor use and equipped with
a splashproof coupling-socket
 
- always keep away the cord from
the hot air ow and the air outlet/
nozzle
- keep the cord away from heat, oil
and sharp edges
- do not carry the tool by the cord,
and do not yank the cord to
disconnect it from the socket
- do not suspend the tool by the cord
Never use the tool in conjunction with
chemical solvents
Make sure work area is adequately
ventilated
Keep work area clean and well lit
Keep children away from work area
Ensure that children do not play with
the tool
Inrush currents cause short-time
voltage drops; under unfavourable
power supply conditions, other
equipment may be aected (if the
system impedance of the power
supply is lower than 0,127 +
j0,079 Ohm, disturbances are unlikely
to occur); if you need further
clarication, you may contact your
local power supply authority
Stay alert; watch what you are doing,
use common sense and do not
operate the tool when you are tired
Take a secure stance; do not
overreach, especially on ladders and
stages
Ensure that the tool is switched o,
before putting it aside
In case of electrical or mechanical
malfunction, immediately switch o
the tool and disconnect the plug

Switch o the tool and disconnect the
plug
 

Suspend the tool on hanging ring
D 2 or set it down on its rear in an
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 8003 CC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 8003 CC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info