390161
8
Zoom out
Zoom in
Previous page
1/108
Next page
8
- the pressure control feature is specically designed for
fast sanding at maximum sanding speed (speed
control setting 7), for it is the need for fast sanding that
provokes applying too much pressure
! be aware that the working of the pressure control
feature is not guaranteed when sanding at lower
speed control settings (1-6)
On/o
- before switching on the tool, you should place it with
the entire sanding surface on the workpiece
- when switching on, do not apply too much pressure on
the tool
- switch on/o the tool by pulling/releasing trigger F
! be aware of the sudden impact when the tool is
switched on
! before switching off the tool, you should lift it
from the workpiece
Switch lock
- pull trigger F 2
- press knob G 2 with your thumb
- release the trigger
- unlock the switch by pulling again trigger F 2 and then
releasing it
Speed control 7 (7460)
For optimal sanding results on dierent materials
- with wheel H 2 you can set the desired sanding
speed
- always adjust speed to grit size used
- before starting a job, nd the optimal speed and grit by
testing out on spare material
Holding and guiding the tool 8
! while working, always hold the tool at the
grey-coloured grip area(s)
- guide the tool parallel to the working surface and move
it in circles or in a cross pattern
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots K 2 uncovered
Sanding
- the amount of material removed is determined by the
speed of the sanding disc
- the speed of the sanding disc diminishes relative to
the pressure applied to the tool
APPLICATION ADVICE
For determining the optimal grit (and speed), table 9 can
be used as reference
! always test out first on a piece of scrap material
For more tips see www.skileurope.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool and cord clean (especially ventilation
slots K 2)
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 0 will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60745, EN 61000,
EN 55014, in accordance with the provisions of the
directives 2004/108/EC, 2006/42/EC
Technical file at: SKIL Europe BV (PT-SEU/PJE), 4825
BD Breda, NL
Á»½ʽËÁ¼½ÆÌ
ȽʹÌÁÇÆËŵÆ¿Áƽ½ÊÁÆ¿
ÍÊÇȽƓˁ˅ʿ˂ʽ¼¹Ɠ
ÈÈÊÇιÄ¹Æ¹¿½Ê
21.07.2011
NOISE/VIBRATION
Measured in accordance with EN 60745 the sound
pressure level of this tool is 82 dB(A) and the sound
power level 93 dB(A) (standard deviation: 3 dB), and the
vibration 7,7 m/s² (hand-arm method; uncertainty K = 1.5
m/s²)
The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for dierent applications, or with dierent
or poorly maintained accessories, may signicantly
increase the exposure level
- the times when the tool is switched o or when it is
running but not actually doing the job, may signicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 7460 aa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 7460 aa in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info