591193
6
Zoom out
Zoom in
Previous page
1/108
Next page
6
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
dierent from those intended could result in a hazardous
situation.
5) SERVICE
a) 
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR SANDERS
GENERAL
 This tool should not be used by people under the age
of 16 years
 Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
 Never use the tool when cord is damaged; have it
replaced by a qualied person
 This tool is not suitable for wet sanding
 Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
 Certain kinds of dust are classied as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
 Follow the dust-related national requirements for the
materials you want to work with
 Do not work materials containing asbestos
(asbestos is considered carcinogenic)
 When sanding metal, sparks are generated; do not
use dust bag and keep other persons and combustible
material from work area
 Regularly clean the power tool’s air vents (the
motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards)
 Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
 SKIL can assure awless functioning of the tool only
when original accessories are used
 Do not continue to use worn, torn or heavily clogged
sanding sheets
BEFORE USE
 Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
 Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
 Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
DURING USE
 The noise level when working can exceed 85 dB(A);
wear ear protection
 Wear protective gloves, safety glasses, close-tting
clothes and hair protection (for long hair)
 Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
 Do not touch the moving sanding sheet
 In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
 If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
AFTER USE
 When you put away the tool, switch o the motor and
ensure that all moving parts have come to a complete
standstill
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
 Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
 If for any reason the old plug is cut o the cord of
this tool, it must be disposed of safely and not left
unattended
USE
 Mounting of sanding sheet
4
! disconnect the plug
- if necessary, clean backing pad rst
! perforation in sanding sheet should correspond
with perforation in sanding foot
! the dust suction requires the use of perforated
sanding sheets
! always use the tool with the total sanding surface
covered with sanding paper
! replace worn sanding sheets in time
 On/o switch
- switch on/o the tool by pushing switch A
2
forward/
backwards
! before the sanding surface reaches the
workpiece, you should switch on the tool
! 
from the workpiece
 Dust suction
5
! 
up performance
- remove dust bag B by pressing knob C and hold it in
that position while pulling dust bag backwards
- mount dust bag B by sliding it back until it clicks into
place
- for using vacuum cleaner remove dust bag B and
mount vacuum cleaner to connection D
! do not use dust bag/vacuum cleaner when
sanding metal
 Speed control (7348)
For optimal sanding results on dierent materials
- with wheel E
2
you can set the desired sanding
speed
- adjust speed to grit size used
- before starting a job, nd the optimal speed and grit by
testing out on spare material
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 7348 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 7348 in the language / languages: All languages as an attachment in your email.

The manual is 3,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info