389477

Skil 7210 fox 2 in 1 Manual

4
Zoom out
Zoom in
Previous page
1/44
Next page
4
INTRODUCTION
● This tool is intended for dry sanding and finishing of
wood, painted surfaces, plastic and filler
TECHNICAL SPECIFICATIONS 1
SAFETY
● Read and save this instruction manual (pay special
attention to the safety instructions at the back)
● Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
● Always keep the cord away from moving parts of the tool
● When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
● Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
● In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
● We recommend to use original SKIL-accessories as
listed at the back of this instruction manual
● This tool should not be used by people under the age of
16 years
● The noise level when working can exceed 85 dB(A);
wear ear protection
● If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
● Never use tool when cord is damaged; have it replaced
by a qualified person
● Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
● This tool is not suitable for wet sanding
● Do not sand material containing asbestos
● When sanding metal, sparks are generated; do not use
dustbag and keep other persons and combustible
material from work area
● Do not touch the moving sanding sheet
● Do not continue to use worn, torn or heavily clogged
sanding sheets
● Wear protective gloves, safety glasses, close-fitting
clothes and hair protection (for long hair)
● Wear a dust protection mask when working with
materials which produce dust that is detrimental to
health; inform yourself beforehand about the materials to
be worked on
● Always direct the cord to the rear away from the tool
● Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
● Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
● If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left
unattended
USE
● Mounting of sanding sheet
! disconnect the plug
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot 2
! replace worn sanding sheets in time
! always use the tool with the total sanding surface
covered with sanding paper
WHEN USING TOOL AS AN ORBITAL SANDER 3
- remove delta tip A while pushing button B
- mount rectangle C by inserting tabs in holes at a 45˚
angle and pushing it towards housing until it
snap-locks
- mount VELCRO sanding sheet as illustrated (do not
remove part 2)
WHEN USING TOOL AS A DELTA SANDER 4
- remove rectangle C while pushing button B
- mount delta tip A by inserting tabs in holes at a 45˚
angle and pushing it towards housing until it
snap-locks
- mount VELCRO sanding sheet as illustrated (remove
part 2 and keep it for using tool as an orbital sander)
● Dust suction 5
- mount dust bag
- empty dustbag regularly for optimal dust pick-up
performance
! do not use dustbag when sanding metal
● On/off switch
- switch on/off the tool by pushing switch D 5
forward/backwards
! before the sanding surface reaches the
workpiece, you should switch on the tool
! before switching off the tool, you should lift it
from the workpiece
● Holding and guiding the tool 6
- guide the tool parallel to the working surface
! do not apply too much pressure on the tool; let
the sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep the ventilation slots uncovered
APPLICATION ADVICE
● Use the tool as an orbital sander for large working
surfaces (wooden table-tops, floors, doors, stairsteps, etc.)
7 8 9
● Use the tool as a delta-sander for edged, narrow and
other hard-to-reach places on your workpiece
(window-frames, staircases, furniture, etc.) 8 9
● When the foampad of the delta-tip is worn or damaged
at the top, you may extend its service life twice by
tearing it off, turning it 120˚ and putting it back
(also applicable to delta sanding sheet) 0
● Never use the same sanding sheet for wood and metal
GB
XP SKIL 7210.2 31-03-2004 12:23 Pagina 4
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Skil 7210 fox 2 in 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Skil 7210 fox 2 in 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Skil 7210 fox 2 in 1

Skil 7210 fox 2 in 1 User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info